I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
I am looking to check signal strength and would like to be able to do it as easily as possible.
The default asset_tracker sends messages which can be seen in the nrfcloud...
We have an application running on our devices that are using ble_nus to communicate with a base station.
The use case is approximately something like this:
On button presses...
Step1 : init a Client model in Provisoner:
Step2 :config this client:
Step3:set the pub address of this client & control the remote gen_onoff_Server model: but it...
Hi
I've found an issue with the serialization code for the function sd_ble_gap_device_name_get in the SDK 14.1.0. As far as I see the issue still exists in the SDK15.0.0...
Why did Nordic deprecate the -30dBm TX power setting on the nRF52832? The current TX power settings jump from -40dBm all the way up to -20dBm, Why the power jump of 100X?...
HI Nordic Team :
Our important customer uses nRF52832 to develop bluetooth key product . they want to know how long the 52832 enter IDLE mode by calling WFI instruction...
I am using nrf52832, SDK 15.2, Softdevice 6.1, Embedded Studio to program a custom PCB device. My aim is to eventually send data I have from a peripheral device (through SPI...
Hello Nordic Support,
I would like to know if I don't specify the CFLAG -mfloat-abi but have floating point calculations in my code for NRF52832 target, does the compiler...
Hi,
I use NRF52840 on a custom board. I am utilizing low-level SoftDevice flash API for accessing flash:
sd_flash_page_erase() and sd_flash_write().
I want to register...
What would happen if using the recently released Programmer app from nRF Connect v 2.6.1 for PC, you accidentally erase all de contain inside the Device Memory Layout window...
Hi
Can anyone please explain me as how to change the start address of flash (while using soft device) and changing the start address of RAM too. I am working on nRF52840...
I'm looking at the patched version resulting from applying the pc-ble-driver patch, but this might be present in the original as well.
675 case APP_USBD_CDC_ACM_USER_EVT_RX_DONE...
Hello,
I'm trying to receive a 2-byte data from a sensor from Maxim Integrated MAX31875 but the nrf_drv_twi_rx function only receive 8 bits data. Does this function to receive...
I'm evaluating the NRF9160 DK, and have run into some interesting issues.
I find that the AT client works, sort of, though it's quite flaky and I quite often get timed out...
