Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Some Examples discuss background DFU from application level, but those require bringing in IPv6 stack and TFTP client. Since we are planning to integrate DFU of our device...
I got nrf_cloud_connect failed: -111 error while running asset tracker demo.
I know that I need to flash certificate files according to my previous question: https://devzone...
It looks like the DK comes with a coin cell type battery and there seems to be a tab that can be pulled off to activate. However I don;t see any mention of this in the documentation...
Hello,
I am developing product on nrf52 with sd s112_nrf52810_5.1.0_softdevice. My application caused unexpected sd fault at adress 0x000089B2. I expect it to be something...
Hi all,
I am using my android ble application , but I don't manage to receive data sent from the application to the device ( nrf52840 )
I am using the ble_app_uart example...
Hi all, I got the requirement to actually know the path of a message from a client to server(s). Is it possible to add a few bytes of data until the message reaches the server...
Hi
I'm using NRF52840 + SDK15.0.0 and softdevice 6.0.0
I have joined two program one is ble_app_uart and other SAADC capturing ultrasound noise. (Saadc program works perfectly...
Hi,
I have a nRF52 DK board and I am trying to build a BLE peripheral with both connectable advertisement (custom with my own name and service) and unconnectable advertisement...
I'm developing in a freeRTOS environment. One thread is sampling the ADC using PPI at 200Hz, which various other threads sample Sensors via SPI and finally I'm using the NRF_LOG...
Hi,
I'm designing custom PCB with nRF52832QFAA chip and after custom PCB population I can't make SWD to get working. In order to eliminate where the issue is I would like...
Hi,
I have RF-BM-ND01 (nrf51822) BLE4.0 module and i am programming it using nrfjprog tool. and i am using nrf SDK12 to program examples. i tried to flash softdevice S130...
I am using SoftDevice S132 v3.1.0 and I have a high priority application ISR that cannot tolerate being interrupted by the SoftDevice. The ISR occurs once every connection...
I'm trying to understand the limitations and configuration options for the mesh stack, in particular what happens when the mesh becomes busy.
From studying the code it appears...
I saw in the ble_app_ancs_c routine, the broadcast initialization function has the following definition：
init.advdata.uuids_solicited.uuid_cnt = sizeof(m_adv_uuids) / sizeof...
I tried to upgrade only a part of firmware of application, not all. I used buttonless DFU and found that the new code was located at bank1 and not moved at the specified address...
