I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hello everyone,
right now I have two BMD-340 Evaluation Kits which used nRF52840 module and I want to evaluate Bluetooth Long Range and Data Rate of this module. I used...
Hi
I saw a fail for RF-PHY/RCV/BV-29-C on nRF52840 DK.
But I also find it is a known issue as "Anomaly 172 Addendum".
In the nRF52840_Rev_1_Errata_v1.2.pdf, two workarounds...
Hi,
I'm working with the nrf52840-DK and using the nRF5 SDK v15.2.0 Stack version.
I´ve got a working program for my coordinator (C) and my end device (ED). The C establishes...
Hi
I have this code that works like a charm when the device is connected and I want it to leave the network.
But if the device is dead or disconnected and I want to remove...
Hi,
I know this is a license question and the default answer is "contact a lawyer if you don't understand the license". But this can hardly be the first time someone...
Hi,
I'm trying to connect nrf52840 to IOS 12.1.4 as a Braille display. Standard BLE HID is working well, but when I try to connect as a Braille Display ( Settings/General...
I am trying to connect and according to the spec sheet, there might be multiple pipestatusevents.
When I try to connect using different phones (with different Bluetooth...
Hi,
I'm using the light switch client example to test the Mesh App on iOS.
The PCA10040 board can be identified through Mesh App, but not be identified on our test board...
I am using nrf52810 chip without softdevice or bluetooth stack. I started to develop at November 2017 with Datasheet version v1.2. On 31. Januar 2019 Nordic released a newer...
Hello,
I have project for collecting temperature information from 15 pcs temperature sensor.
It is possible to create system with 16 pcs nRF52840.
one of them will be...
Hello,
I’m using two nrf52832 as servers sending 20 Byte data with 18 ms notification interval.
Notification Data:
[incremented uint8_t ] [19 byte data]
Client:...
Hi,
I'm working with the nrf/samples/nrf9160/at_client (@ tag v0.3.0) with a PCA10090 board.
I had a question about the response to the AT+CESQ command.
Specifically...
hi,
i am quite new with programming tools like the nordic thingy and i am currently trying to get some initial program running, i.e. the blinky example. i have a few questions...
