Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
I have some question about nRF52832 Bluetooth Firmware upgrade problem:
1. I have a device with nRF52832 in my hand. If I don't use the JTag interface, how can I confirm...
Hi,
We are using Nrf51 with SDK nRF5_SDK_12.3.0_d7731ad
We based a UART bridge on the BLE_APP_UART example
The UART connectivity is Rx/ x only (RX_PIN_NUMBER 0; TX_PIN_NUMBER...
Hi,
we've noticed that after performing an OTA DFU, the Bluetooth Address of the device changes as follows: new_address = old_address - 1
Example: Address before OTA DFU...
Hi there,
I am a beginner to the nRF series and I had the following question.
For a battery powered system, is it better to run the nRF52840 at a lower voltage such...
Hello,
i'm trying to program on 51422. The BLE signal,which runs well on 51DK, doesn't trigger any signal on my own PCB. i've successfully light the LED on my PCB. i think...
Hi,
I'm using nRF52832 and I'm trying to switch from SDK15.0 to SDK 15.2. While I've been able to install micro-ecc library in SDK15.0 and use OTA DFU, somehow I'm stuck...
Hello.
I want to integrate UART and SPI ,I am using SDK15.2. The problem here is i am not able to add app_uart.h to main.c(spi).
My question here is how to add it to main...
My working platform is nRF52-DK, and I want to execute DFU firmware upgrade
1. How to create a Bootloader Image? Which Source-Code of SDK_15_2 is used to build the bootloader...
The RTC documentation states that the LFCLK source needs to be explicitly started by the software.
Is this step necessary when using the SoftDevice? As far as I know, the...
I'm not sure about how does the ble_app_att_mtu_throuthput example works exactly, i supose the throughput test runs as follows:
1 tester defines a service 'populated' with...
Dear all ,
Working with nRF52832 (currently without SoftDevice), and there some issues regarding the project current consumption that we need to understand:
1) In the...
Hi,
I am having a trouble trying to make a custom service from SDK 15.0 ble peripheral template example. I have followed the tutorial from : https://devzone.nordicsemi.com...
Hi i'm a newbie, Got Thingy:52 (Keil and J-link) and want to develop HOGP keyboard application. Where can I find Tutorial or example ?
Is there a step by step guide on how...
