I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Hi,
I have been working with Bluetooth mesh. The test I have been performing repeatedly polls a single node and measures the RSSI (as measured from p_message->meta_data...
Hi,
I purchased Thingy:52 I want to develop ble mesh n/w application on Thingy:52.is it possible that I get any sort of support from you in this context.
I'm trying to run the Thread DFU examples on nRF52840, unfortunately I can't get them to work. On the client, I got the bootloader set up and ready, with the client application...
Hello!
I don't quite understand how to properly link NFC tag library (nfc_t2t_lib_gcc.a) to Segger Embedded Studio Project.
Steps I did:
Add nfc_t2t_lib_gcc.a...
Hi Nordic
Do you have a message sequence chart for how to do a Gatt Client Write with response? I can only find a GATTC Characteristic Value Write Without Response in the...
We are using the nRF6707 power profiler kit to measure our EVB’s current consumption in advertising mode. We use the example app ble_app_pwr_profiling. The only change is...
Hi,
Is there any example of adc (saadc) and uart throw ble?
I want to take same measurements from fotoresistor and send data via ble_uart i found same example but no...
I have a problem in selecting inductor(L1). In NRF52832 IC datasheet, mentioned specifications of inductor L1 are: 3.9nH, 0402 high-frequency chip inductor. What should be...
I am writing a bluetooth mesh application with a server and client.
Provisioning is working, but the configuration of the server is giving me problems.
I have based my...
Above image is our design for nRF51822. Design also contains Accelerometer and WiFi (ESP8266).
My problem is, I am not able to see nRF BLE advertisement while scanning...
Hi!
Can someone please help me debug this example. It used to work, then I changed number of peripheral links to 1 (to see what RAM suggestion would be), then returned it...
Hi!
I try to flash nrf52 from keil and message appear:
The firmware of the connected J-link (S/N: xxxxxxxx) does not support the following memory access: Read @ 0x02000004...
Hello,
I want to enable UART only when data transfer is necessary.
I am using nrf 52832 and sdk 14.0.0.
I am using "ble_app_uart".
I could not find the answer I...
Hello everyone.
I have a question about sleep_mode_enter() behavior.
I'm using nRF5_SDK_12.3.0 and nRF51822 for my project.
I put a lot of printf statements in the example...
Hello All,
I am working two BLE chipset , one is nordic and another one different make (TI) so is it possible to communicate between two different make BLEs using our nordic...
