Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
I want to make a secure pairing with Bluetooth. Let it first pair with the device, then connect directly without pairing. Maximum how many devices can I register?
Hi,
I'm using an nRF52832 in SDK v.17.1.0 and, starting from the ble_app_uart example code, I'm sending data from the board to another device. I want monitoring it with...
Hey all,
I'm looking for a bit of guidance here to nail a bus fault that happens about 30 minutes into the program.
The message is the following:
Reading through previous...
Hello
I am trying to test the esl example project.
Is there a simple, accurate, step by step guide for this?
Current documentation has some incorrect sections and when...
Hi Team
Customer want to use Bluetooth_Base_UUID (00000000-0000-1000-8000-00805F9B34FB) as 128 bit UUID base. They can use any other 128 bit UUID base but this one. When...
Hello, I'm working on an application with precise timing requirements. Basically I need to generate a short pulse and sample two channels during the pulse. In addition, I...
I use the nrf5340.
I want to filter 8 devices with different addresses.
When scan_filter_match() recognizes one of the addresses, can you quickly identify which of the...
Hello, I built a matter-over-thread firmware for nrf52840 on the Matter SDK 1.3-sve branch and NCS 2.5.0 version. It work well with Apple, Google and chip-tool, but commissioning...
Dear sir or madam,
I am facing a peculiar issue. In my application, I am using nrf52840 dongle and I am setting several GPIO pins as output pins with output value high...
Hello DevZone,
I am developing battery powered Zigbee end device. Using nrf Connect SDK 2.6.0 on nrf52840 chip.
I have issue that I am trying to solve. From time to time...
Hello there,
I was using 2.5 SDK on my development. Recenelty I updated the SDK to the latest of 2.7.0-rc3. I got many warnings.
Then, I created a brand new BLE NUS project...
We have a product that uses nRF52832 and works as a peripheral, connecting to mobile phones. Lately we have noticed that in some clients with Android phones, they cannot connect...
Hi,
I am using nrf52840 and SDK 16.0. I have already used SPI 1 and SPI 2 instances.
Now I am using SPI3 instance. Initially SPI 3 is initialized in non-DMA. and it worked...
Hello,
I am inquiring about the development guide for the coexistence of BLE and WiFi using the nrf7002dk board. Since I have recently transitioned from the nRF5_SDK development...