I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hello.
I have two nRF5340 DK boards that I want to use to replicate the demo on https://github.com/NordicPlayground/nrf-knx-iot .
I am using Ubuntu 22.04.
I cloned the...
Hello,
I've developed a custom PCB which uses an nRF52810 SOC. I've been developing the software for the device using NRF Connect SDK 2.6.1 in Visual Studio Code, and I...
The first time I download the program to my device , it will cause a crash when I try to set NRF_POWER->GPREGRET for OTA purpose;
However after restarting my device, and...
I've found an interesting behavior in the less with the Copy button on this step:
I found that if I clicked on the copy button, the spaces in the text are 0xA0, but if...
Hello,
I have enabled the BIS gateway to send stereo signal, and the BIS headset can receive the stereo signal and play it.
Now I can pack the left and right data to one...
I implemented MCUboot in Serial Recovery mode on a custom USB stick to enable firmware updates via MCUmgr. Initially, everything was working correctly, and the image transfer...
Hello~
I am developing nrf52840 with zephyr ncs tool chain v2.7.0 and SDK v2.6.1.
Our project needs RSA to exchange secure data.
I use example "samples/crypto/rsa",...
I am working for 2 years on nrf_sdk with softdevice and FreeRtos on cpu nrf52832
now we want to move to Zephyr OS.
- I installed nrf command line tools. nrf connect for...
We're using the Nordic Zephyr library (SDK v2.5) to configure the nPM1300. Using the library, the battery discharge current limit is set to 1000mA. However, using a logic...
I am trying to make my gateway send stereo data to the headset where it will be played on an external codec. I want this to be a single stereo stream.
I had this working...
Hi,
I was looking into hooking up an SD card to the nRF9160DK that I use for data collection during evaluation and early stage pilot projects. I noticed that there is an...
Describe the bug
BLE pairing on the new NRF54L15DK does not succeed. Connecting and advertising works, only pairing fails. I have tried the same example on the NRF52840DK...
Hi, we are using custom PCB with nRF9160.
we are writing a firmware for radio test lab. We are using LTE asynchronous in our firmware and LTE-M mode. We want the modem to...
Hello.
I am using the nRF5340 DK.
According to the circuit diagram, it seems that when I apply power to VBUS_nRF, there should be no power on VDD_nRF of the MCU.
(Power...
Hi,
for my custom device with nRF52840 and nRF Connect SDk v.2.8.0with VScode I want to add bootloader so that I can pass firmware to it through USB cable. I want a simple...
