Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hi All
I am experiencing an issue with the nRF DFU app (v2.7.0) on devices running both Android 11 and Android 14. The issue occurs when I attempt to perform a DFU update...
Hello,
I want to run mass storage on my custom board with the nRF52833 and W25Q512JVEIQ. I have reviewed the mass storage sample (ncs\v2.7.0\zephyr\samples\subsys\usb\mass...
Hello,
I have a custom board with an nRF52833 and a W25Q512JVEIQ, which communicate over SPI (not QSPI). I successfully accessed the W25Q512JVEIQ (executed my own read and...
Hi, I am using nRF52832 module BL652. I want to measure the battery voltages of a 9V battery. What are the best possible resistors value to measure voltage of such battery...
Hello, We have a custom PCB with both the nRF9160 and nRF52832. Currently, the nRF52 functions as an HCI controller connected via LPUART to the nRF9160. We're at the stage...
Dear sir:
When I first use CHIP tool in my Ubuntu NB, I can commission bulb(52840) through OTBR(Pi4+52840 RCP) successfully, besides, I can use CHIP tool to control bulb...
Hello,
I am currently checking the RSSI measurement precision, and we got very large errors (up to 10dB error) on the RSSI vs input power.
To avoid any PCB / matching...
I'm new to nRF5340 development, and I'm reviewing partitioning for multi-image DFU. I've enabled the bootloader with CONFIG_BOOTLOADER_MCUBOOT=y , and after checking partitions...
Hey,
I am having an issue where my device doesn't show up in the Nrf Connect app as "connectable" despite as far as I can tell being set as a connectable device. This doesn...
Hello,
I'm trying to upload code to an external board using an NRF52dk, and am having an error in vscode as shown below.
My issue seems to be very similar to the one...
Hello.
I understand that Radio Notifications is an API that notifies you before and after scheduled radio events occur within a SoftDevice, but can you tell me more about...
Good day
I have the NRF_desktop keyboard application running on the NRF52840 Dongle, Zephyr 2.6.1. I would like to us the nrf52840 ProMicro as it has a battery charger build...
Hi,
I would like to know Number of UARTs available for Murata 2AB. According to the 2AB datasheet, there is one UART, but the nRF52340 datasheet shows two UARTs. Can 2AB...
HI,
I am building "esb_ptx" sample in NRF54L15-PDK, by using CONFIG_DYNAMIC_INTERRUPTS, but it;s always reset like below;How to config the prj.conf to enable CONFIG_DYNAMIC_INTERRUPTS...
