Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hello, I want to purchase cables to connect a Flasher Pro (cable should end on DB20 Female) to an nRF52-DK onto "Debug In" connector (cable should end on mini DB10 Female...
Hello, I am developing a solution based on nrf52-DK, using nRF52832.
I am trying to use JFlash to read Device Serial Number. I could read it with JLink , with command "mem32...
Hi, hope someone can help me.
The past 3-4 years I have used SDK 17.1.0 and SES for SW development where the SW is running on a nRF52840 SoC which is the heart of our product...
I'm working on a Docker image that includes a VS Code server for the purposes of workshops and training, and I'd like to install the nRF extensions (e.g. https://marketplace...
hi，bro
I want to support both BLE and GZLL simultaneously and perform the corresponding initialization work based on the value of a variable, mode . However, when I set...
Hi,
I have difficulties to sniff BLE packets with nRF52840 and wireshark between a remote controller and phone.
I can capture all the pairing process, I see DHKey exchange...
Greetings!
I am looking into Bluetooth Mesh, and the allowed radiated power according to Norwegian law. The general limit for 2.4GHz is 10mW, but if we utilize FHSS the...
Hello, I'm running into an issue with the "modem shell for NR+" application on a pair of nrf9131ek evaluation kits. The local sales rep. suggested that I reach out to Nordic...
Hello, I have a pair of nRF9142EK devices that I've been using to test DECT NR+. Now, I'd like to test out one of the boards with the cellular modem firmware for nRF9131EK...
Hi Support team,
I am using nRF9160 module and i want run two server on the module, one is modbus server and other is CoAP server. so is it possible to run both server...
When using the adafruit feather nrf52840 , the lowest I can seem to get power usage is around 400uA (including with the boards/nordic/poweroff sample ) .
This is my device...
Hello
I'm exploring the mesh dfu transfer, get some strange results
Here is the setup
1 distributor, 1 target
On the distributor I start the transfer with mesh models...
Hi,
I need to setup shell interface on both sides to exchange sensor data via uart.
The connection is as follow: cable 1: nRF52840DK Pin (TX - P1.02) → nRF9160DK Pin...
