Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi,
I have an application called `main_repo` built using v2.1.1 (the SDK version doesn't really matter). This contains all source code, dts files, Kconfig files, etc. to...
hello Nordic
trying to migrate from ncs 2.5.0 to 2.7.0
well i did the mistake of installing the toolchain via the vs code .. for some reason it installed it in the wrong...
DFU is now implemented on ipads and iphones, as well as on Android phones, and the app platform is nRF Connect. The problem is that the firmware upgrade can be achieved normally...
I was trying to build off of the example of Lesson 6, exercise 3 from the Intermediate course on DevAcademy.
https://academy.nordicsemi.com/courses/nrf-connect-sdk-intermediate...
Hi there,
I am trying to interface SPH0465 microphone with nRF Dev Kit 52832 with the following configurations of I2S:
I have followed the code from echo example...
Hello!
I am hitting a really frustrating issue running Zephyr on a XIAO BLE Sense module which is based on the nRF52840 MCU. I am simply trying to verify development setup...
Hello,
On a pairing failure from iOS (either cancel or timeout of the pairing dialog alert "Bluetooth Pairing Request"), the device no longer allows pairing until a software...
Recently our firmware team encountered a new version of NRF52840 and our hardware team "orders the available chip". How can I know and manage the version when we design the...
I was wondering whether having GATT client and server in same chip (NRF52832) would work? If so, then how would I need to set up bt_conn_auth_cb on zephyr if both uses passkey...
Hi,my board is nRF52840dK,and the SDK is ncs 2.7.0.
I want to modify the subevent parameters,
Is there any API to modify them in my code but not in prj.conf? such as ...
The provisioner sample was used as the base code for adding the function to set model's publication address. After doing so the end node goes into
Requesting Help regarding...
I currently am using a nRF9160DK. I want to have the nrf52840 on it scan for BLE devices and return the device count and then send this over UART to the nrf9160.
How can...
Hello,
I am contacting you today because I recently bought an nRF5340 development kit, as well as several Nordic Thingy devices (52, 53 and 91) and I have been working on...
Hello,
I am contacting you today because I recently bought an nRF5340 development kit, as well as several Nordic Thingy devices (52, 53 and 91) and I have been working on...
Hi, I was reading through the errata for SoftReset and see a note: [161] RESET: Network core is not fully reset after Force-OFF
Can you please clarify how to reset both...
