Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi,
I want to use the onboard 5340-DK QPSI flash for saving binary data into, however when i enable the support for it i get that the device is not ready. I have tried both...
The above is my code.
This is running log.
After scanning multiple times, my application may freeze, as shown in the log, and there will be no response after receiving...
I am developing a project on nRF9161.
I am interested in calculating data usage for different protocols (for example MQTT with TLS) when communicating with a server over...
Hi,
I refer to the method of the link below, which can generate factory_data.hex
https://docs.nordicsemi.com/bundle/ncs-latest/page/matter/nrfconnect_factory_data_configuration...
I am attempting to write a routine that monitors the heap in order to track down a memory leak. I've seen similar tools on other platforms and found them quite helpful. To...
Hi,
Previously I have merged spi with ble_app_uart on NRF52832 based ISP1507 test board . It has performed successfully which was enough to carryout the evaluation phase...
Hi. experts, I tested [TC-ACE-1.2] Subscriptions with Test harness, which is UI-Python. I execute it on Docker,./certification-tool/scripts/otbr/otbr _ start.sh; And write...
Hello.
I'm trying to figure out which microcontroller is best for my use case. I need to have as many bluetooth low energy concurrent connections as possible and the device...
After rummaging through the awful and extremely limited documentation relating to external programming using the NRF52840 DK (so I don't have to pay for the $700 scam device...
Greetings
I am trying to use the BLE fundamentals exercise (Lesson 4 exercise 2 solution) to send actual sensor data, that I receive via I2C, to my nrfConnect app.
When...
I have a question about for LE. In my understanding, BT connection must confirm each profile, and it is able to connect same profile that each products have. For example,...
Hi,
I just wander why in the peripheral UART sample for the nRF5340-DK (ncs, SDK 2.7.0), the prj.conf doesn't include the internal capacitor configuration:
prj.conf file...
I realize that Bluetooth is the primary target of these devices these days, but I wanted to try an old tried and true example on the nrf5340. I am rather familiar with esb...
Hi,
When I try nrfsdk/zephyr/sample/bluetooth/periodic_adv_rsp, after changing subevent_interval to 8, I meet following error:
*** Booting nRF Connect SDK v2.7.0-5cb85570ca43...
