I read this older post ( devzone.nordicsemi.com/.../) and have a similar issue but with enough differences that I felt it was worth a new question.
I have an STM32 MCU...
I am having an issue with running the initial blinky example that came with the nRF51 PCA10028 SDK in the Eclipse IDE . I will include screenshots of the issue. I believe...
I use nRF51-DK and nRF51-Dongle for a BLE sniffer.
Always the sniffer fails and marked with an error "Encrypted packet decrypted incorrectly (bad MIC)".
It can not be...
Hi,
I'm using long write in one characteristic but if I try to configure this characteritic with write authorization (attr_md.wr_auth = 1) it doesn't work. I need to send...
Hi, I disassembled an Acer Mouse and saw a chip named "NRF A 3152c 1517UH". Can anyone identify the chip or provide me with the data sheet for it.
Regards,
Steve
After i asked this question , i changed to use SDK 8.0.0 hrs "s110_for_dfu",
As the same step to try,
i downloaded softdevice(s110) & bootloader(for 8.0.0)
then opened...
Hello All,
I am trying to create multiple threads for an individual tasks. But when I am creating new thread my program is not working and it's going into some infinite...
Dear Support Team,
Hardware : nRF5340 Custom board
Software : nRF Connect SDK v2.2.0
I have implemented OTA FW update for nRF5340. I've used multi-image simultaneous...
Hello ,
i am trying to find out advertisement handler while SD advertising in SYSTEM ON mode.
i have added a simple counter to see if it is increasing or not but it is...
Hello fellow developers!
I am currently working on a scale application using the nRF52 DK, and I've run into a roadblock regarding the integration of the HX711 load cell...
Good morning,
I would like to know if I can work with Zephyr with C++ and how to do it.
development software, with versions:
Windows 11
nRF52840-DK PCA10056, 3...
Hello
I'm suing the smp_svr sample from the Zephyr SDK 2..6.1
I want to change the CONFIG_MCUBOOT_IMAGE_VERSION to force the OTA DFU ( over bluetooth ) but when I add...
Hello Nordic Team,
I am writing because I encountered an issue while developing a BLE application on the nRF5340 development board. Currently, I have set up this callback...
With multiple of the provided samples with the SDK, I'm getting a repeated build loop that ultimately fails due to a remaining "dirty build.ninja". This is primarily with...
Hi,
I am working BT840F which has nrf52840, I am using ble_app_uart example to transfer UART data to app. I wanted to know what is the system frequency of the microcontroller...
Hi,
I am using an external flash on the NRF52840DK via SPI and have established working communication with the flash memory. However, I need to disable CONFIG_SPI...
In my project, using nrf52840 controller, I am trying to store 253 bytes of data in NVM, but I encounter an error: "flash_nrf: invalid address: 0x00100ff8:8." Is there any...
Hello DevZone,
I'm porting my project from NCS 2.5.0 to NCS 2.7.0.
I know that there are lots of changes in build system, especially in Zephyr sysbuild. So, I decided...
Hello, I was able to update nRF Connect SDK to v2.7.0 fine using nRF Connect for Desktop. However, the nRF Connect for VS Code extension update v2024.7.13 causes VS Code launch...
Hi,
As described in the subject I'm not able to set "Extra High Drive" for a GPIO. This setting is described in 7.13.5.11 in product specification version 1.3. I'm able...
