Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
I created xml file for heartrate server using bluetooth developer studio and the plugin nRF8001_Arduino (plugin nordic semiconductor for arduino)
the generated xml file...
I read this older post ( devzone.nordicsemi.com/.../) and have a similar issue but with enough differences that I felt it was worth a new question.
I have an STM32 MCU...
Now we have bound the corresponding pins in the device tree, and there is no pin multiplexing except for LED and BUTTON. However, now as long as we configure SPI in the main...
I'm trying to use the nRF Desktop project as a base for our project, prototyping on the nrf54l15dk_nrf54l15_cpuapp board target. I have an overlay file defined like this:...
Error Report:
When flashing, I get this error:
Error:
One or more batch tasks failed: * 1050058878: Timed out waiting for response from worker. (Generic) FATAL...
Hello Nordic Team, I have referred this post and am aiming to create an empty bare metal project on nrf54L15 for BLE peripheral with GAP read, write, notification and idicate...
HI
I am currently using nRF54L15 with NCS 3.0.0 SDK, running the periodic_adv_conn example. I made the following modifications to the extended advertising and periodic advertising...
We have noticed an issue with our device built on nRF5 SDK + nRF52832 when connected to iOS 26.
Initially after connection, everything is ok. Then we attempt a connection...
I am porting nRF SDK 2.6.1 to SDK 2.7.0 on the nRF5340. For the network core, where exactly should the kconfig (prj.conf) file be located and named? On the sysbuild migration...
Hi, based on the previous struggle with data transfer drops with nrf9161 ( ) we came after the cooperation with Vodafone MNO to the situation, that (at certain test place...
I'm using the peripheral_bms project. The only change being in the overlay to make it work with nrf52833 dk. I'm able to connect with nrfConnect and see the services (except...
I'm developing with the NRF52840 using IAR Embedded Workbench , and implementing wireless communication based on the IEEE802.15.4 Zigbee protocol .
In the MAC frame layer...
I am new to Nordic and want to design with the nRF52840. I have read this guide:
used AppCAD to find the best width and clearance for the ground layer, but when I downloaded...
Hello, I am using NCS 3.0.2 on nRF52840. I have been using MCUBoot for a long time on my device, and it is working fine. Recently, I went through a requirement where I needed...
Hey everyone,
I've been trying to get the Bluetooth Mesh DFU Target sample working on my nRF5340 DK and running into some issues. I've read through the docs.nordicsemi.com...
Hi All,
I have an nRF5340 Audio DK which has problem with the network core. When I connect the USB to board or try to recover the board the MCU light at the bottom of...
