Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
I created xml file for heartrate server using bluetooth developer studio and the plugin nRF8001_Arduino (plugin nordic semiconductor for arduino)
the generated xml file...
I read this older post ( devzone.nordicsemi.com/.../) and have a similar issue but with enough differences that I felt it was worth a new question.
I have an STM32 MCU...
I am having an issue with running the initial blinky example that came with the nRF51 PCA10028 SDK in the Eclipse IDE . I will include screenshots of the issue. I believe...
I use nRF51-DK and nRF51-Dongle for a BLE sniffer.
Always the sniffer fails and marked with an error "Encrypted packet decrypted incorrectly (bad MIC)".
It can not be...
I can successfully perform a DFU of my BLE device via the Nordic "nRF Connect" App using a nRF52 DK. I'm trying to do the same via nrfutil CLI, now running into an issue:...
Hello,
I'm working with the nRF Connect NVS module on the nRF9160. Every time there is a read/write to NVS the messages:
I: 3 Sectors of 4096 bytes I: alloc wra: 0, 668...
Hello With Zbus being added to Zephyr, are there plans to carry on support for the Application Event Manager and the CAF or switch to using the Zbus system in future releases...
Hello,
I am new to the microcontroller development club and have recently obtained a nRF52 DK kit. I am using the new nRF Connect SDK and have the Arducam OV5642 camera...
Hi there,
We have developed a family of BLE products based on the NRF52832 using it's maximum TX power 4dBm.
We have a strong push for increasing the communication range...
I have a simple application running on our custom board based on nRF52840. Our board does not have any uart pins connected so we use RTT exclusively for console I/O. I attempted...
Hi! I am trying to use the Power Profiler app on my Windows computer, I have used it on another Windows computer, and it worked fine. Now, when I try to open the PP app, it...
I’m working on a project trying to characterize the range (given a certain transmitter and environment) on the BLE 1 mbps PHY. I’m using a few nRF52840 dongles to do this...
Hi,
I am evaluating nRF5340 audio dk with CS47L63 DSP. My goal is to find out the MCU processing consumption for LC3 codec what is MCU processing power left for the application...
Hi,
I am writing a program that sends numbers counting up sequentially from my dev board to my phone on 500ms intervals. I used the ble_app_uart example as my base. I am...
Hi all,
I trying to use test-harness v2.6 raspi and nRF52840dk to test commissioning. The result is always failure, and the error is timeout
The firmware DK flash is build...
I have a red pulsating light on the dongle.
dmesg shows it is being detected, on Ubuntu 22.04
[203496.636885] usb 3-3.1: USB disconnect, device number 40 [203508.682046...
Hello,
I have a nrf5340 and pc based on Windows OS. I want to transmit information from 5340 to pc at a speed of 300kbps. Here are my two plans:
Using BLE protocol...
Hi all ,
I had my code working on nRF connect 1.6.0 and now had to upgrade it to work with nRF connect 2.1.2.
I read the migration guide for nRF connect 1.x.x to 2.x.x...
I have tested sending NUS data from nRF52832 to laptop (Windows 10 + Intel core i5), but Windows app doesn’t received all NUS data. But When I tested sending NUS data from...
