Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
Hi,
I'm trying to save system uptime when the watchdog callback occurs.
The NVS functionality works when calling nvs_write elsewhere in code.
Calling nvs_write inside...
Other Configurations:
prj.conf
# General config
CONFIG_LOG = y
CONFIG_LOG_DEFAULT_LEVEL = 4
CONFIG_STACK_SENTINEL = y
CONFIG_NEWLIB_LIBC = y
CONFIG_NEWLIB_LIBC_FLOAT_PRINTF...
Refering to following discussion:
mqtt-messages-received-multiple-times-on-qos-1-subscription
Our application is based on SLM application from nrf connect sdk 1.3.2. There...
Hi, I am using nRF52832 module (GAP peripheral, GATT server) with nRF5SDK, ble_app_uart_pca10040_s112 application.
In ble_app_uart application, how can I ensure that UART...
Hi,
I'm a real novice with this but I'm having this issue and I can't see how to resolve it.
Building HeartRate_sensor west build --build-dir c:\Users\deirdre.hackett...
hello Nordic
i am want to run an ncs based application (that is running on nrf52840, -> trying to create single code for 2 boards i have), when i set to run the same application...
Hi,
What are the geofence capabilities in BLE Mesh ? What are the possible features that can be implemented in the view of geofence. My point is like the mesh node if it...
Hi, All
I am trying the example here ...ncs\v1.9.1\zephyr\samples\bluetooth\central_multilink\ with nRF52833dk_nrf52833 board, however it doesn't build, and saying the maximum...
Hi,
1. I want to use BOTH LTE and GPS, which example is the most intuitive to verify.
2. What instructions or functions should be used for SWITCHING between LTE and GPS...
Hi,
1. How to prohibit nRF9160 from automatically re-registering to NB network after disconnection( This is to solve the problem of high power consumption when signal is...
Hello, We have a product using an nRF52840, with the SDK17.1, the 140 Softdevice, and an application based around the Nordic UART service (nus). We are seeing application...
The global search function does not find search terms that must be in the project. Under SES I could simply do a global search and instantly find the definition of an object...
I am using the nrf Connect v1.9.1 SDK. I am currently trying to read the battery level for the CR2032 battery for the nrf52dk_nrf52832 build. There are two different approaches...
