Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
I created xml file for heartrate server using bluetooth developer studio and the plugin nRF8001_Arduino (plugin nordic semiconductor for arduino)
the generated xml file...
I read this older post ( devzone.nordicsemi.com/.../) and have a similar issue but with enough differences that I felt it was worth a new question.
I have an STM32 MCU...
We need to read/write to an I2C device that uses a 16-bit register addresses (Melexis MLX90632), and the nrf_drv_twi_tx() and nrf_drv_twi_rf() functions seem to be limited...
Hi,
We would like to impelement Pairing and security features in our device. Our device will act as server in peripheral mode. The cleint device should ask for 1 passkey...
Hi Nordic,
I'm referring to this doc but still not quite clear about how to enable the chip for BLE RF HW validation.
infocenter.nordicsemi.com/index.jsp
What would...
Hi,
I have modify the payload of the Light Switch example of the NRF MESH SDK. When I send 50 bytes or less, all works fines : the server nodes received all the bytes...
Hi everyone,
I am developping on a custom board using nRF52840, using MCUboot v1.8.99-ncs1 and nRF Connect sdk v1.8.
For development matters, I would like to change the...
Hi, I want to include the pairing and bonding features in my application.
I want to use the LE secure connection method. For both initiator and responded the IO capabilities...
I adding custom pins declarations through overlay file as in first image with corresponding yaml file ( see attachment) with path .. /dts/bindings/gpio/custom.yaml. The project...
Good Day. I am wondering if anyone could maybe assist me in where I am going wrong with my software.
I have the intention of using a Nrf9160 as a serial modem through AT...
I use nrf9160 to develop a product for customers. The modem is also set to PSM and the log is turned off. However, I find that when the modem is connected to the Internet...
When I try to connect to nrf52840 using J-Link, the following error is detected.
What is the reason for this "Failed to power up DAP"?
- Connecting via USB to probe/ programmer...
Hello nordic support:
We want to measure nRF9160's LTE RX SNR at production stage .
According to the document nwp_034--nRF9160 Hardware.pdf ==> 4.6.1. Following command...
Hi, I am working on nRF52832 as central. When I program it to form Segger Embedded Studio it's working fine but when I upload that .hex file from the nRF Connect device did...
Hi there,
We are designing a coin cell (3 V nominal) battery powered product; we'd like the ability to run it all the way down to 2.0 V for maximum lifetime. To get the...
Board: nRF52833
SoftDevice: s140
SDK version: 17.0.2
I am trying to implement OTA buttonless DFU feature in my custom device (USB Device) which is a central device....
