I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hi.
I'm using PDN example code on zephyr nrf sdk. Please take a look on below log.
Can somebody help me to figure out what are the API can be used to send and receive...
Hi,
Using VisualStudioCode/NRF Connect: Im looking into the sample 'button'. (this because i like to add GPIO-pins to connect to an interrupt)
In the button example...
Hi,
I'm using Manjaro Linux, nRF Connect v3.10.0 and Programmer v2.3.3. I'm trying to connect to nRF52840-DK using this software, but I get an error:
I can connect to...
We are working for "Lighting control model" using BL653 controller ( nrf_653dvk connector) .We are looking for a Test automation framework to test BLE mesh and BLE FUS Based...
Hello nordic. I'm using your FTP client. The client can only send 4 kB of data at once so I send data numerous times and append to a file. The first send I do is 160kB which...
Environment:
nRF52833 (BL653 module from Laird)
nRF 5 SDK 17.0.2
S113 v7.2.0
I'm running into a really odd problem that I can't track down. If I set APP_TIMER_CONFIG_IRQ_PRIORITY...
I am using nRfdongle(nrf52840dongle), Getting timeout error while writing new .hex file to the dongle.
Using nRf programmer app write new .hex file to the dongle. have taken...
We are in the process of designing the nRF52833 into a product which uses the BLE direction finding capabilities.
I wanted to check if we should avoid using the pins that...
Goodday all
Im experimenting with Vscode and Nrfconnect (zypher library). I want to see how easy it is to port my Segger nrf SDK code to vsCode. Having trouble getting it...
Hi,
I am trying to integrate Visual Studio to the nrf SDK and gnuarmemb using the instructions provided. However, I keep getting an invalid toolchain error although I have...
In SDK 1.9.0 i saw that QSPI deep power down was implemented and i can confirm that that works using the below code. The issue I see is that if the device is in deep power...
Hi,
Is there any sample/example that comes with SDK that shows how to add extended data in BLE advertisement (using Zephyr)?
I have tried adding some additional bytes...
We have 3 nRF52840 to establish a net. one for master device, One for Master device, One for HUB(Msater-Slave) device, and One for Slave device. The data flow is Slave device...
Hi,
Following the update of my mac (M1) in Monterey, i can no longer flash programs on my board (everything worked under Big Sur).
I got the error JLinkARM DLL load...
Hello,
I am currently trying to add a FEM (nRF21540) to an already existing BLE project that is using nRF5 SDK. For that purpose I ordered the nRF21540 DK that is using...
