I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
We used the nRF52840 in some projects, but there are still some problems with the short bridge at the IC during production.
So we want to leave the blank layout of the unused...
HI
We have to try to develop a product with nrf5340. The product needs to be waterproof and also it made up of metal and a small amount of plastic enclosure. In that how...
Dear Members,
I want to run ANT+ code in my custom board,
It works well on PCA10056, I can upload softdevice and the code to custom board board,
but I didn't get any...
I've recently upgraded my SDK to 1.6.0 and I am now unable to read the state of P1.00 but I am able to read the state of P0.28.
I've stripped the project down to just a...
I recently installed nRF Connect SDK using the Toolchain manager. Install went through without any issue but when I am trying to open an example project in SEGGER Embedded...
Hello,
I have a nRF52840 and am unable to flash an application to it. I am trying to flash the "examples/ble_peripheral/ble_app_blinky/hex/ble_app_blinky_pca10059_s140.hex...
Hi Team,
What is the meaning of BLE advertising link encryption and data encryption,That makes no sense .In glucose example the DH computation is calculating can you clarify...
Hello All,
I configure ADC & BLE UART in one code. we are using 4 ADC channels. but I observed that there is a timing delay approx 2-3 sec to update ADC. we are using a...
Hi everyone,
I wanna implement the wakeup from SYSTEM OFF by button. The project is based on the ble_app_uart example. After receiving a command from BLE, nrf will go to...
All,
Before I head off on that experimental path, was wondering if anyone on here tried to parse and convert project.yml to Cmake arguments? We use ceedling for unit testing...
Looking to see if anyone has run into this issue and how it was resolved. We have a nrf52832 running sdk 15.3 (also tried 17) sd 132 6.0. We are using the pwm module + nrf_drv_pwm...
I recently started using the gatt queue as a mechanism to buffer and send HVX notifications. At times our system may produce asynchronous notification events faster than the...
It is great to have VS Code as IDE. Thank You.
Yet, I do not find a valid configuration that allows me to use IntelliSense or even simple include paths during coding. The...
I would like to establish bonding between my device and an android phone.
My device is acting as both a central and peripheral. It functions in peripheral role in relation...
