Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Bluetooth low energy, Direct Test mode nor RSSI Viewer is working with my nRF5340DK board. For instance with RSSI Viewer it says "Error while setting up device XXXXXXXXXXXX...
Hi
I need to build a communication between nrf5340 and esp32 using UART Protocol. I need to transfer some data from nrf5340 to esp32 and vice versa via UART. Already, I...
I want to add Service based on the Bluetooth base UUID which is 00000000-0000-1000-8000-00805F9B34FB When I am trying to add it using "sd_ble_uuid_vs_add", it always returns...
nrf52805 is being used as a GATT server using a static passkey. An ESP WROOM 32 is being used as a GATT CLIENT. The issues is that nrf52805 sends a disconnect to ESP32 after...
Hi,
I'm trying to run an example in which is in below link but seems something is missing in the documentation seems also all commands returns "OK" but no response from...
i am using VS code, nrf Connect SDK version 1.7.0, nrf 5340 DK board. Attempting to run the CLI example.
The Cmakelist.txt:
#
# Copyright (c) 2020 Nordic Semiconductor...
I've got another question concerning a timeslot application.
In our timeslot application which is based on the nRF Mesh SDK timeslot.c implementation I noticed that if a...
I have a device using nRF52840 with SDK 15.2.0 and S140 6.0.0. It has failed with some kind of error. All core registers (including PC, LR) contain DEADBEEF. PRIMASK = 0xef...
I'm working on NCS 1.6.1.
I'd like to confirm if my method to get the RSSI is correct.
i test with a sample "peripheral_uart"
after BT connected, i printk the (NRF_RADIO...
I am testing the %XRFTEST Rx Test Command with the thingy91, with serial_lte_modem_2021-06-28_7a076c22.hex FW
and nRF Connect - LTE monitor software
I used the command...
The Repository link in the extension page on VS Code marketplace points to https://github.com/NordicPlayground/vscode-nrf-connect but that only returns 404 not found. I've...
Hello,
I am using the nordic nRF52840-DK and trying to connect to a nRF52840-Dongle and sending/receiving data to custom services and characteristics using pc_ble_driver_py...
Hi
I need to know, Is there any wifi module that supports for nrf5340 to communicate cloud or server??. If it is available kindly suggest us.
Thanks & Regards
Navin...
I am using Fanstel's BT840F BLE module which is based upon nRF52840 for my application. I am using PCA10056 DK to program it. I tried to program the BLE module on the DK with...
Hi,
We are using SDK13 and nrf52832.
I want to do multi pairing using Mode 1 Level 4.
Is there an example of multi-pairing and an example of deleting bonding individually...
