I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hi Sir/Mdm, I want to use 1.54 inch e-paper module from waveshare with nRF52840 dongle with Zephyr RTOS. I have read the documentation from Zephyr about the display and noticed...
Hi,
We use the nRF52840 and have now run out of space using debug mode compilation (using CMake from bash).
When we compile in release mode, we get 50% full flash, so...
Hi,
I am using nrf52832 and mesh sdk 3.1.0 with nrf5 sdk 15.2.
We use dual bank approach for our firmware update with the normal nrf5 sdks ble bootloader. But now our...
Hi.
I have been trying to implement my own Model into the Light Switch Example (Mesh SDK 4.2, SD s140 7.0.1, Hardware: nrf52840 DK), according to this Thread:
Adding Simple...
I'm implementing the WS2812 driver on custom hardware and have some confusion around the hardware tuning parameters for the SPI implementation. The description of the device...
Hi everybody,
We ran into a Zephyr configuration issue which is related to Zigbee and Zephyr's networking stack. In our setup we would like to use Zephyr's modem library...
Hi,
I have nRF52840 DK, for nRF52 series devices. I switched from nRF52 SDK to nRFConnect SDK.
I reviewed
http://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest...
Hello,
I am running ble_app_beacon demo from nRF5 SDK 17.0.2 on nRF52 DK and would like to decrease power consumption as much as possible. From this post , I have seen that...
In the official development board directly burn SDK routines, input the command to write data in the serial port, if you continue to input, for example: interval 1s to write...
Hello everyone:
We use NRF52840 to test the transmission function of mesh and verify the minimum publish(client)-->prescribe(server) time;
The following is the publish...
Hi,
I have nRF52840 -DK boards.
I was using nRF SDK (SoftDevice ) to program nRF52 devices. Now I am switching to nRFConnect SDK. nRFConnect SDK is new to me. A few questions...
hi，
My application MTU exchange is 23 bytes，I send data using Notification or indication to sent 105 bytes date，I subcontracted the data into 20 bytes ot sent，How do I make...
How do I do memory debugging in the nrf52840 in the runtime, or trace the RAM in run time, also how do I do the profiling of the memory in the run time. How do I find out...
