I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
1. I've deleted the peers from the device by running the BMS sdk example, still i am unable to connect the previously bonded device where i"ve deleted the key.
2. The pm_evt_handler...
I get NRF_ERROR_FORBIDDEN error when I want to send a software message to the server device in the Light_switch application, except for the button. But when I press the button...
Hello,
I used exampl:
nRF5_SDK_17.0.2_d674dde/examples/ble_peripheral/ble_app_hids_keyboard
Why can't I see any HID Services in apps (nrf Connect) in iphone 12?
But...
Hi, I've read that when NFCT is operative the internal resistor of SoC is automatically adjusted. For antenna tuning this resistance can be set to a fixed value through a...
Hi there,
My current setup:
1. Custom board.
2. SDK nRF5 SDK v17.0.2
3. Application running BLE (SoftDevice)
Using the USB CDC Class example to be able to interface...
I'm using nRF51 sniffer to capture BLE packets for group of devices. Sniffer can able to capture only primary advertisement channels and not secondary advertisement channels...
Dear Members,
I want to use this code :
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.sdk51.v10.0.0%2Fant_examples_bpwr.html
Does it work...
Excuse me:
As shown in the figure below, can this type of crystal oscillator be used on nrf52832? How to connect this crystal oscillator with XC1 and XC2 of nrf52832?
Hi,
we are preparing for certification and are about to test with the DTM v1.0. now in nAN43 it states following:
1.1.1 Hardware requirements • nRF8001 Development Kit...
I try to add pairing/bonding to the NCS hello world project. But I found the information is not easy to find. I'm playing with the bt_conn_auth_cb struct to understand how...
Hello,
I am trying to verify a signature with the `NIST p-256` curve. I had previously done this with the Nrf5 sdk and it is working:
I am now trying to migrate...
Hello Nordic Team,
as a newbie in the Nordic world, I have been reading the nRF Connect SDK and Zephyr documentation as well as testing some of the samples on my nRF5340DK...
Hi.
I have some trouble to use a sensor based on JDY-23 module with nrf52832 dk
(JDY-23 datasheet : ://fcc.report/FCC-ID/2AXM8-JDY-23/4936741.pdf )
We tried to connect...
