Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi,
I get BLE_GATTS_EVT_WRITE with connection handles 16 and 19 which seems to be some defaults of the softdevice.
Can you explain the source and usage of these connection...
Hello
I am working with aws_iot sample and over this I add gps functions (handler and work init) belong to agps sample, I probe AT%XMONITOR command and show me this
...
I build the example and download to PCA10040,but there no log print in RTT, and I debug in keil mdk, I found the program does not step into main function.
How to run this...
I have an application that requires that timestamps be 64-bit epoch to the millisecond. I'm currently using a Timer peripheral to track 1ms and increment a 64-bit counter...
Hi,
How can I make the device generate random address periodically? I searched on the forum and found people mentioned BLE_GAP_ADDR_CYCLE_MODE_AUTO when call sd_ble_gap_address_set...
Hi.
I have a product that acts as a peripheral, and bonds with centrals that are typically smartphones. Normally the peripheral uses a whitelist to only connect to bonded...
So I noticed the program goes into a state where it's stuck on NRF_BREAKPOINT_COND , which happens after getting into the following writeToLogger () template function. If...
Hello,
I am evaluating NCS 1.5.99 zephyr's sample"periodic_adv"and"periodic_sync"with two nrf52833 DK. The sample "periodic_adv" runs normally on nrf52833 DK.But the sample...
Hello,
I've been trying to use Zigbee Endpoint Logger for the light_bulb and light_switch sample. But I can't make it work. I've been looking through the quetions on this...
Hello guys, i want to implement nrf5-calendar-example in nrf51822 with SDK 12.3.
This library can use RTC0/RTC1/RTC2. But i have only RTC0 and this RTC0 is for SD (am i...
hello,
if i want to connect to a peripheral device with strongest RSSI. I need to get the RSSI before connecting.
and i know i can get the RSSI from event of BLE_GAP_EVT_ADV_REPORT...
I'm trying to read the values from the DS1307 RTC through TWI. I've established a connection with the device but am not sure I'm using the nrf_drv_twi_rx() function correctly...
Hi,
I'm trying to run the peripheral heart rate service example on a custom board using the internal 32kHz RC oscillator. However, the code hangs when soft device is enabled...
