Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
I'm running NRF Mesh3.1.5 in Android on my Galaxy S10. I'm following the steps in the Bluetooth Mesh Developer Study Guide and can connect to the Switch an Light nodes as...
Hi,
I wanna my appication run first instead of bootloader. Here is my steps:
Create bootloader_setting: nrfutil settings generate --family NRF51 --application application...
Hi,
I have a card with some large capacitors in parallel with the VBAT line. How does the PPK2 work (in source mode) at board start-up where there might be a short in-rush...
I have a question. The sample code I modified is nRF52832\examples\ble_central\ble_app_uart_c. Scanning will be triggered when scan_start() is called. The device has been...
I have change the version of wireshark on windows 10 .(NOW I?M USING THE ONCE OF THE APPLICATION NOTE)
After that i have modify the .bat file because he never see python...
Hi,
My provisioner is a light switch client on a dev kit NRF52832.
Now I want to define it as a proxy node as well but I suspect that my Android App cannot send one generic...
Sorry I'm looking in the AoA.
I See that in zephyr main line there are 2 samples :direction_finding_xonnectionless_rx direction_finding_xonnectionless_ tx..
Hawe I to...
Hi,
I am trying to program new chips. I have made the following connections:
Chip J-Link ------------------------------ Gnd Gnd SWCLK SWCLK SWDIO SWDIO VDDH 5V (External...
Hello:
We have a BLE application on an NRF52840 with SD 140 and SDK 1.5.3. Our device acts as a BLE peripheral with bonding and LESC, and we additionally use block level...
Hi,
We have designed the custom PCB where 32.768 kHz crystal oscillator is required. Some how we have managed the component (MFR PART NO. TF325J32K7680 ) suggested by Nordic...
Hi, I came across a forum post that NRF51 had an issue with noises in SWCLK signal.
For the design, do I need to attach an external pull down resistor in design? If so,...
Hi good evening,
i am working on a project that requires ble transmission between 2NRF52dks and one of them is connected to a PC and apart from receiving data from another...
Hi Devzone,
I have 2 question about Thingy 91:
1) When I come to area that don't support NBIoT or LTE-M, Does the Thingy 91 connect to cloud (nrf cloud, mqtt broker,....
