Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi!
I am trying use aws iot sample and over this the gps example to obtain location and transmit a aws iot core, but I have problem with manage of lte and gps functions...
My project uses nRF52840-DK to connect, bond and discover a custom service with two characteristics (TX and RX) and RX Characteristic has a CCCD (0x2902).
The flow of the...
I am using nRF5340 DK board to implement zigbee network.
I have just build connect SDK's zigbee example (network Coordinator) and seen utilization of RAM shown below.
...
Hello everyone.
I am trying to set the attributes' value of a custom cluster I have defined.
I have defined 2 attributes:
I have followed the same procedure...
Hi,
We are designing the Nordic 52840 into a product and had some questions about the power configuration:
For both REG0 and REG1, are there any downsides to selecting...
SDK version: nRF5_SDK_15.3.0
Platform: nRF52840 DK
--
I use ble_app_blinky example and use nrf5-calendar( https://github.com/NordicPlayground/nrf5-calendar-example ...
Hi,
I am new to nrf9160 and zephyr. I was using the SD card and a breakout board on SPI bus to write the raw data coming from the PDM interface on nrf9160 Feather. Before...
Hi Nordic DevTeam,
I have successfully done DFU through nRF Connect both on Android and iOS after merging ble_app_uart (combine ble_dfu_buttonless application here) & secure_bootloader...
Hi,
I am developing projects for street lightning system and I use in my projects many CoAP libraries. In my projects I use OpenThread and some peripherals like UART....
Hi everyone,
I use the nrf5_SDK_for_Mesh_v4.1.0_src, I would like to reduce the time it takes for a device to connect to a bluetooth module as a proxy. For the moment this...
Hello all,
I try to get the asset tracker v2 to work against a eclipse mqtt broker. For the first steps I use the mqtt.eclipseprojects.io broker before I hosting my own...
We are developing a device with the nRF52805 for BLE communication. The firmware was developed for nRF52832 and converted to nRF52805 following Nordic's documentation. The...
Dear Nordic support,
Could you please give an advice regarding usage of Zephyr SPI driver / NRF SPI driver with Nordic nRF52840? I've faced with the issue that driver can...
Hi!
I've shipped a whole bunch of PCBs out to customers where pin P0.21 is attached to an IC (which pulls it low by default).
Usually this is fine as the preinstalled...
