I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hi Nordic,
I got the following error when I try to open nordic sample project in SES workbench...May I ask what happened? Thanks
Creating solution base.emProject ...
Hi, I have use nrf driver_ext / LIS2DH12 sensor driver to read accelerometer data
I can able to link the driver with nrf_twi_sensor and nrf_twi_mngr code.
I can able...
Hello All,
I am working on NRF9160. I was checking the HTTPS_CLIENT Example. But in my application I wanted to use the link that has header as well. How can I modify the...
Hi
I am currently trying to append the CTE extension to a normal packet using the tx and rx examples from the SDK. The examples I am using are in examples/peripherals/radio...
Device: nRF5340DK, PCA10095
I'm using latest nRF Connect SDK, installed by nRF Connect - Toolchain application.
I opened central_uart sample:
I added only "LOG_INF...
Hi,
I have already implemented a full project on NRF52840 and all is working well.
Now I need to implement FOTA through BLE.
I have 4 questions please.
1. Can I...
Board: nrf52840 DK SDK: Zigbee 4.1
Hello,
I am currently in the process of reducing the power consumption of our application. One method I want to explore is switching...
We are using nRF52840 DK with SDK17, our aim is to achieve Eddystone packet advertisement and connectable mode using FreeRTOS. Implementation started with ble_app_blinky example...
Hello,
I want to use BLE Direction Finding solution. However, I couldn't find any documents or any software library. Is there support in SDK for direction finding ? Are...
I request detail information about the UART internal implementation of the UART in the nRF52810 microcontroller.
Many application are used in noisy environment.
From other...
Hi
I am trying to flash the device with the bootloader, the soft device and the application, because I do not want do the OTA update at production.
I used the following...
Hi,
I want to control leds of nrf 52840 board through raspberry pi 3 B model uisng python.
I used interactive pyaci example for provisioning nrf sdk board, but it requires...
I am using NRF52840 development board with SEGGER Embedded Studio (Nordic Edition)
I downloaded example code to target board. The software run with Zephry. I found function...
I tried to follow this tutorial to set up the Connect SDK toolchain with CLion. It worked until I resetted the CMake Cache. Now it always gives me this error message.
...
