Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
I need to read (and clear) the general purpose retention register. I cant start the Soft Device just yet, so cant use the sd_power_gpregret_get and sd_power_gpregret_clr functions...
Hi there!
I'm back again, with another possibly stupid mistake. I'm using ARMGCC in combination with Make, nRF5 SDK, nRF SDK for Mesh, FreeRTOS and C++. I wrote my own mesh...
Hi Dev team,
I am currently using the NCS v1.5.0 and have a Thingy91 v1.4.0 with me. I want to test the FOTA v2 update from the nRF Cloud to the Thingy91.
I tried using...
I am trying to tune my NFC antenna . The antenna is printed on the pcb. The same Laird antenna is used in my pcb. Based on the antenna tuning white paper I am trying to tune...
When I connect my Thingy 91 to my usb port open up nrf Connect and push Sw3 and turn on the board power I do not get any devices to show up under device selection in rf connect...
In our application the prospective Nordic NRF5340 MCU is to communicate with another MCU at the maximum 3Mbps.
Can this speed ( 3Mbps) be achieved on NRF5340?
As mentioned...
Hello, I'm hoping that I missed something in the code and not something that might be inherent with nus and fds. Combining SDK 15.3 template, uart and fds examples, with some...
Hi,
We have a working solution on the SDK15.0.0 with a custom board based on nrf52832 s132. I'm using the nrf52dk PCA10040 to program my boards. For this board we use...
Hi,
for my system implementation with nRF52840, I use the Nordic Uart Service based on the nrf_ble_uart example.
I transfer sensor data every 10msec, or so, to BLE uart...
I've been digging through the DFU in order to reduce it's power and I've come across 3 high power states.
1) The first is during initialization of the DFU. It happens on...
I have been dealing with this for 6 months and im running low on time to finish this project please help me. I want to send 20 bytes of data to a application that i made for...
Hi,
We are using Micron NAND flash MT29F8G01ADBFD12 with QSPI. We are referring qspi, usb_msd example in sdk 17.0\examples\peripheral\usbd_msc. Able to read device ID of...
Hi, I have a problem in enabling both NAME filter and UUID filter in ble_uart_c SCANNER
I have enabled the both but
the device get connected only match with UUID but i...
HI
I am using the example of HTTP and HTTPS from this github link. I was unable to compile the example of HTTP and the HTTPS example is just hanged. no communication. I...
