Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hi,
I'm using NRF52840 device to connect to a mobile via BLE.
Sometimes, I have error 133 and disconnection.
Can I initialize my BLE in a different way (characteristics...
int main(void) { bool erase_bonds; ret_code_t err_code;
log_init();
{ // Initialize the async SVCI interface to bootloader before any interrupts are enabled. err_code...
Hi,
I am using nrf mesh 5.0 sdk and nrf 17.02 sdk for nrf5832 board and want to implement scene setup server model in the light ctl and light lc model combined. I am not...
Hi,
We are working on our new product which needs a BLE connection with a mobile phone.
Our requirements are as follow:
1) Four digital output. (It's preferred to be...
Hello,
From the ble_app_uart example I created a version where instead of the UART the incoming data over BLE is processed using the scheduler.
Processing is not much...
Hi, i develop a bluetooth project with nrf52832 anad i am unexperinced about this topic. I searched for 2.4 GHZ antenna desgin bu can't found. There is a few topics about...
HW: nrf52833-DK
SW: SDK v16.0.0 and SoftDevice s140
We are using nRF52833 BLE direction feature and read IQ samples produced by BLE Radio.
The format of the IQ samples...
I am working on porting a project from the old sdk to the nrf5340 and the nrf connect sdk documentation seems to be incorrect and i am having major issues even getting this...
SoC: nRF52810
SDK: 17
Hello,
I want to confirm whether BLE_DFU_ENABLED is used or not.
InfoCenter ( https://infocenter.nordicsemi.com/topic/sdk_nrf5_v17.0.2/group__ble__dfu__config...
Hi,
I use the app "asset-tracker", and i would like to configure an external uart to connect a sensor to the board.
I modifed the code but i can't detect any new COM from...
Hi,
I am using nrf51422 and s130 softdevice for multirole. Is there any way to reduce the receiver power during scanning so that the overall current gets reduced?
Hi,
I'm trying to implement remote provisioning on an altered version of the light switch example in the SDK for Mesh v3.2, on nRF52832 development kits. The code I'm using...
I am using nrf52832, i want to send the sensor data continuously via ibeacon.
but while uisng sd_ble_gap_adv_set_configure() function return error NRF_ERROR_INVALID_STATE...
