Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hello,
I am working on a Proteus III module which work with a nrf52840 SoC. I am using nrf52840 DK to test and develop code and at the same time testing the codes in the...
Does the nrf_cc310 support interrupt operation? I want to start the calculation of a hash/asymmetric signature but don't want that the CPU busy-waits until the calculation...
Hello,
I am trying to do make a connection with sd_ble_gap_connect();
First i am scanning all the devices arond and i am filtering with my functions using with ble_gap_evt_adv_report_t;...
Hi, I'm using nRF52832 Software Development Kit, PCA10040, S132.
I'm trying to connect the hrs central to my device and read the data from that. But the feature of my...
Hello, I am writing the firmware to the product in the J-Link and nrfjprog. The command is used in the same way as described in the Makefile, and is used in general. Normally...
Hi,
I'm trying to integrate the USB CDC ACM example into a project that I'm currently running on an NRF52840 DK with SDK 16.0. My PC is running windows 10 and python 3...
Hey, I'm trying to set up a simple timer that fires an interrupt every so often (100-200ms), but I'm having trouble. My interrupt keeps firing continuously, but I think I...
Hello,
I have been trying to program my own Provisioner. While testing I accidentally had a nRF52840 Dongle plugged in with a client running on it. It automatically connected...
I'm working on a cli_uart application on a PCA10040 board using SDK 17.0.0. I started out by using the SDK peripheral example for twi_master with twis_slave as a base for...
I'm trying to implement CLI over BLE UART for one of our company projects. I started from the experimental ble_app_cli example in the SDK. I'm using SDK 15.3.0 on the Nordic...
Trying to build asset tracker for Thingy91 following the instructions at https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/ug_thingy91.html
I get:
and...
SDK 16
nRF52840 with s140
Hello,
I'm working on implementing an assert handler and would like to store the file/line hash in NVM. I currently have fstorage configured...
HI..i am trying to implement multilink central with nus service..but it is getting error at lbs_c_init();.what is the reason..can anyone help..i also changed the central link...
Whenever I try to debug my code, it gets stuck at fault_s_S as shown below
I experienced that one of the possible solutions to avoid this is to browse fw_info.h when the...
