I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
I am trying to use the ble_eddystone_app on a nrf52840 dongle. The way this app appears to work is so: 1. device starts in advertising but not connectable mode
2. pressing...
Hi team,
I am using SDK V16.0.0 and looking at the flash_fstorage_s140 example. There are wait_for_flash_ready function calls after the nrf_fstorage_write function calls...
Does the nRF52 ( or anyother product ) support ASHA and MFI audio streaming?
It looks like ASHA is supported, I found this:
https://github.com/nordic-auko/nRF52-ble-audio...
Hello,
We're bringing up custom hardware using SiT1532 MEMS 32kHz oscillator. This part outputs a low swing single ended clock source (300mV +/-55mV p-p). I'm struggling...
So we are creating a peripheral with a characteristic meant to keep the central synced with the state of our peripheral. The peripheral is running all the time, could be ON...
1. This is on the stock LPN example, with one change to debug-print `status_code` inside handle_appkey_add().
Here is the diff:
2. To reproduce:
- flash and provision...
Hello,
I am currently working on a product with nRF51822 chip, based on SDK10.0.0. The problem is, after a firmware update, my device fails to reconnect to an Android mobile...
Hi,
I've launched wireshark + nRF52 Dongle successfully and I'm also able to select my device (named EWAT AI-No) from the list to sniff. However there's something I don...
I'm working on a simple project based on the USB CDC ACM and libuarte example, the chip is nrf52840.
A function is redirect the USB VCP data to another MCU via UART, just...
Can a server and a client of dimming example, have same element instead of different element ID.
I got worked for server and client model in single node, but they are in...
I am upgrading to SDK 15.3.0 and SoftDevice v6.1.1 from SoftDevice v2.0.0 (S332 stack). Most of functionality has been ported (BLE and ANT) and validated. This particular...
Hi, I'm trying using a setup with transmitter based on nRF24L01P and receiver with nRF24LU1P using Enhached Shock Burst. The problem is the transmission lock (three failed...
Hi,
I am planning system with a BLE peripheral (using nRF52840) and BLE Central (using nRF52840) that is AC powered.
The peripheral will be advertising every ~300msec...
Greetings,
We have some custom boards/devices with nrf9160. They each hold certificates to communicate with aws-iot. The certificates were flashed using the at_client...
Dear nordic,
I am developing a robot controller(Central, nRF51822).
However, I am having a problem with UUID.
And I am using the ble_central (s130 ble_app_uart...
