I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
I want to store a few parameters in flash. I don't want to use an external EEPROM because it takes an additional space on a board.
Does anyone know how to do it or a sample...
Hi,
nRFConnect is behaving differently for apps on different SDK versions. I am able to do a DFU via script something similar to the one here https://thegecko.github.io...
After much work I can build the nRF9160 at_client sample project and flash it into the development kit. Using nRF Connect, the at_client sample project only prints the line...
Hi There,
I have developed an initial application on SDK11, based on the UART example, with Keil and it worked perfectly with the nice low power that you guys are capable...
Hi,
I have created a project with nRF52840 DK that reads sensors data and transmits them with BLE UART to my smartphone. Everything works fine.
Then, I tried to do the...
i am working on mesh application using two nrf51822 and one nrf2832. I started from light-switch examples. nrf51 set as two server and nrf52 as a client . In server side integrated...
Hi all,
in the datasheet of the nRF9160 is mentioned, that the same antenna can be used for LTE and GPS.
Page 364, chapter 8: GPS "Dedicated GPS antenna or shared antenna...
I'm using nRF52840 with SDK15.0.0
Following this tutorial : https://devzone.nordicsemi.com/tutorials/b/bluetooth-low-energy/posts/ble-characteristics-a-beginners-tutorial...
hi,
I'm trying to add a new BLE service to my device. I've followed the instructions in tutorial : devzone.nordicsemi.com/.../ble-services-a-beginners-tutorial , up to step...
Hello,
I have just started working with mesh and I'm using the 0.9.2 Mesh SDK. When I use the Serial interface (nrf_mesh_serial) I don't see any function about rx or rx...
Hi,
I am currently using two nRF52832 SDK boards to implement text message exchange with another nRF52832 SDK board via BLE Mesh SDK 3.1.0 and nRF5_SDK_15.2.0.
the data...
Hello!
I currently have 2 nR52DK using SDK14 and SDK15:
1) Beacon based on the beacon example
2) Central based on app blinky central + multirole
Then, I modified...
Hallo
I'm using sdk12 , S130 on NRF51822, so far successfully updated application, soft device and BL, however
lately after changing the size and starting address for...
Someone have a example of reading orientation sensor in javascript/HTML of the Thingy:52 equal of the github Nordic Example? github.com/.../Nordic-Thingy52-Thingyjs
Hello, I have a problem with staring "Run" in the "debugger mode" . I used Rigado evaluation board with BMD300 (nrf52) and also work with nrf5 SDK_15.3.0 Examples. Sometimes...
