i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
I created xml file for heartrate server using bluetooth developer studio and the plugin nRF8001_Arduino (plugin nordic semiconductor for arduino)
the generated xml file...
I read this older post ( devzone.nordicsemi.com/.../) and have a similar issue but with enough differences that I felt it was worth a new question.
I have an STM32 MCU...
I am having an issue with running the initial blinky example that came with the nRF51 PCA10028 SDK in the Eclipse IDE . I will include screenshots of the issue. I believe...
I use nRF51-DK and nRF51-Dongle for a BLE sniffer.
Always the sniffer fails and marked with an error "Encrypted packet decrypted incorrectly (bad MIC)".
It can not be...
Hi,
I'm using long write in one characteristic but if I try to configure this characteritic with write authorization (attr_md.wr_auth = 1) it doesn't work. I need to send...
Dear DevZone,
I'm new to the nRF52-DK and Nordic in general. I'm trying to set up an nRF52-DK to use with nRF Sniffer, and not having any success.
I have tried following...
Hello!
I want to ask about read operation on nrf51822.
In your examples, as I understand, BT stack handles Read Request automatically and then sends Read Response. The value...
Hello,
I am beginner for bluetooth technology and have very interesting to this technology
I have developed new board (4 pcs) for nrf 52832 and soldered all parts from...
Hello.
Please teach me how to turn on DEBUG flag on Segger Embeddid Studio.
Environment: SDK 15.2.0 and SEGGER Embedded Studio Release 4.10a Build 2018110203.37618 Linux...
Hi I'm facing problem while programming my custom nrf52832 board (It might be issue with flash/ROM setting) its saying this hex file has a data in softdevice region . I'm...
Is nrF52840 VDDH pin only used for REG0 LDO/DCDC regulator output to generate VDD power for the GPIO circuitry?
or is VDDH power used to power some other internal circuits...
Is there a way to access the Gazell heartbeat timer? Ideally I would have a callback to my application when the heartbeat occurs. The main motivation for this would be to...
Hi,
What I did:
Already connected the custom board with nrf52832 chip on pc with python
Already receiving data from the board
I want to have the python code that...
The GPS antenna just fell off the board. Seems like the part has a cold solder joint. This led me thinking that the LTE antenna might also have the same problem. I had no...
I choose one NRF52 DK(nrf52840_pca10056) for my daily development. After hundreds of erase and write cycles, the DK won't behaves like it should do. The other DKs runs well...
Hi,
In the registery definition of nRF52840 it is stated for PSEL.TXD:
Reg ID: A -> from bit 0 til 4 for Pin selection
Reg ID: B -> bit 5 for Port number
In this case...
I am looking into interfacing a SD card to the nRF52840. I have used the FatFS example and that is working ok with SPI. Then I have looked at the QSPI example and that also...
Hello,
I am using sdk 12.2 and nrf52 dk.
I am storing some data in flash using ( sd_flash_write((uint32_t*)0x4F800,m_deadbeef, sizeof(m_deadbeef));) and I am able...
