I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
I wasted way to much time figuring this one out (and after I did find the problem, I realized I had run into this about a year ago in another project :-S)
In my project...
Hello,
I am trying to increase the Peripheral/Central_Link_count to 10 for each or 20 in total and NRF_SDH_BLE_GAP_DATA_LENGTH above 200
I am getting an error when compiling...
I have problem with ble dfu update using zip package with hex + init file via nrfutil. I am getting error Invalid Object when I am trying invoke command nrfutil dfu ble -ic...
Hello,
I am using the NRF52-DK softdevice 6.0.0 and NRF SDK 15.0. The app is based on on the ble_app_template PCA10040e S112 (The final chip will be a NRF52810 that's why...
Hi all,
I'm currently developing a product with the nRF52840 and FreeRTOS using SDK 15.2 where Bluetooth will be needed eventually, but not yet. I originally based the project...
Hi,
I'm using Nordic Mesh 2.2.0 Lightswitch example.
is there possibility of controlling the mesh from a Mobile application which is not a provisioner (basically not...
I have developing one project in that i am using nRF52832 and SD 15.0. Here is the current application developing:
There are 3 ble app_blinky(ble peripheral) example operated...
I have a project based on light_switch example of mesh sdk 2.1.1 now I am migrating to 2.2.0. I mean I have copied entire project from 2.1.1 in 2.2.0
I found this link for...
Hi,
My device does not have IO capabilities so i have used LE secure connection with just works for pairing. since it does not offer any authenticity, i wish to add some...
Hi all,
I am working on a project starting from the smart remote 3 project. I am now developping an app on Windows hoping to do a real time speech to text. Although I...
Hi,
A short summary, while using the app_PWM on our application I noticed an initial pulse on the PWM pin, its a 3V 1ms pulse that happens about 1 sec after powering on...
Hi!!
I am measuring the current consumption of nRF 52832.
However, it shows a very high average consumption current value of 9 mA at all times.
I think that it is probably...
Could I please know the difference between "Simple ON/OFF" model and "Generic ON/OFF" model ? Are both the same and only name is different in SDK versions?
