Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
I'm looking for a Nordic expert. I have already designed and built a complete PCB based on the Nordic nRF52832, along with the firmware. I need to improve the PCB design,...
On my nRF52 DK, I'm seeing *something* pull down VCC by about 50 mV once every millisecond (1KHz), and I'm trying to identify its source. (This is only important because using...
Our application needs to read 128 bytes from 6 SPI sensors as efficiently as possible. We're currently using a single SPI Manager to read all 128 bytes from all 6 sensors...
Hi all.
Just wondering if i need to go through the tutorials on making a service if i just want to read a few bytes in an advertising beacon.
I'm a little lost on figuring...
Hi ,
I am using a bluetooth peripheral which have the Custom Service ID and characteristics ID as below.
Service UUID: 56494B01-0100-1000-8000-00805F9B04E1
Characterisitics...
Hi,
We are currently developing an application that makes use of soft device(s112). We tried using timer(Timer 1) for a timed wake up and sleep but found that the actual...
We are seeing an LMP PDU error when connecting to a Nexus 6p with Oreo (8.0.0) when connecting to an nRF52832 utilizing SDK 14.2 and either s132 vs 5.0 or 5.1 anytime NRF_SDH_BLE_GAP_EVENT_LENGTH...
Been testing custom_ble_service_example , specifically to see if a two byte custom_value can also be used.
But when setting custom_value to uint16_t I get a warning at this...
Hi, I would like to use a PWM application with mesh SDK. However when I try to compile, I got an error because "app_pwm.h" is missing (No such file or directory). The only...
Hi !
I'm using the nrf52832 chip and I'm trying to communicate with a LIS2DH12 accelerometer using the I2C protocol.
But unfortunately I can't handle with it, it seems...
Hello,
I am completely new to creating a Bluetooth mesh network and nRF5 devices. I have three nRF51 DK and 2 nRF51 dongles. I have earlier read the posts and made nRF51...
Hello,
I am using sdk12.2.2 and customised nrf52 board. I am writing 6000 records of 24 bytes each in flash of nrf52. My challenge is after 6027 records I am getting error...
i made custom board refer to thingy 52 Circuit
all fuction circuit is same so i want to use thingy 52 firmware
when i was erase all memory nrf52832 and upload thingy_v2...
I am using nrf52832 sdk14.2.0 to develop now, I want to realize the following function on the basis of PWM_driver example, output the following waveform on P0.22: 1ms high...
