Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
I am struggling measuring time between two events. I thought to use the timer driver and the nrf_drv_timer_capture_get function and start/stop the timer with nrf_drv_timer_enable...
Dear Nordic,
I am try to implement RTC(nrf calendar implementation) in BLE example(SDK 13.0). both are working independently fine but combination of works fails RTC when...
My nrf51 SDK version is like this, nrf51 9.0 softdevice 130 chip:nrf51822_xxAArun ble_central_and_peripheral connectivity example, The nrf51 board is controlled by host MCU...
Hi All, the I/O mapping is correct as per the Ref Eval schematics. We are using a J-Link programmer to program it. The IC is not being detected in NRFgo studio. Can anybody...
Hi,
I was wondering if there is some documentation relating to pairing and bonding.
What BLE events (BLE_GAP_EVT, ???) are to be expected?
What do we need to observe...
I use ble_app_uart（sdk 14.2） + light_switch（mesh1.0.1）
Questions are as follows:
1client + 1server is ok, but in the second server there will be network failure!
log...
Hi,
I'm trying to get the tftp example working from the sdk iot examples. When I try it out following these instructions ( http://infocenter.nordicsemi.com/topic/com.nordic...
Hello,
i'm using the BLE Nano v2 with the nrf52832 on it and a DAPLink USB-Dongle. IDE is Eclipse with gcc and SDK v14.2. My current aim is to do an OTA DFU so I tried the...
I have a custom board, that basically consists of a nrf52832 module (ebyte), a button and a LED. The LED is connected as in pca10040: VDD->220R->LED-> ground to p17.
I assume...
Hi, I'm attempting to run the Proximity example ("ble_app_proximity_pca10028_s130") on my nRF51822 dev kit using the S130 SoftDevice. I am able to connect to the dev kit ...
Hello DevZone, I have few questions relative to the design of the PCB antenna for a nRF52840 chip. I'm going to use the Eagle library find on the github. But... 1) Why the...
It'd be great if the Nordic nRF5 SDK team had a bit more time to test the code under C++, to shake out a few smaller issues.
Here are some changes that needed to be made...
Hello world.
I wanna ask about how to convert arduino code possible for mbed compiler for arduino. first of all, I have tried to use this guy program knn arduino code ....
I'm attempting to build a project to use easyDMA with PWM, but as there are no applicable examples in SDK 15, I am working on it myself. I originally asked for help here:...
