hello, Nrf24LU (Rx) , nRF51822(Tx).
The Nrf24LU Can only receive one packet。
if I use this function twice ， like this：
The Nrf24LU can receive Continuous.
I guess The...
Hi,
I use SDK v10, S110 v8 and dfu_dual_bank_ble_s100_pca10028. My application has dfu support.
I reset to bootloader from application after writing 0x0104 to dfu control...
I have a nRF51822 device.
When the connection interval is 50ms.
The transmission distance can up to 50m+.
But, when the connection interval is 1000ms.
The transmission...
Hi,
I have a simple question. It is possible to use the ble-sniffer nrf51822 on Kali Linux? I found a guide to use it on linux but I don't know if it is the same for Kali...
I've modified Nordic's "Nordic_Keyboard" sample to work with my custom board, just simple modifications to use custom_board.h rather than the default PC10028 configuration...
Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
I am working on nrf52832 BLE. I have used soft device s132. Antenna device is as per the reference design of NRF52832 and have used 32MHZ crystal for HFXO oscillator. but...
I am starting analysis for project of BLE Central device that is only receive broadcasting packet (advertise) from peripherals.
However, it’s unclear to me. I doubt will...
I notice that the sensitivity for the nRF52832 is defined as being ~2dB better in BLE mode than in NRF mode. I have also tested this to be correct.
However, I wonder - is...
Hi!
We have several products which use SoftDevice S110, some of them are already in production and are listed as Bluetooth Qualified, some of them we are preparing for production...
I've a custom board that uses a nrf52832 and Li-SOCl2 battery (3.7V). We've programmed several boards with our firmware and kept then with BLE advertisings every 300ms. A...
I am trying to develop a simple SPI master for a custom nRF52832 uC, but I can't find anny sort of sample codes that don't use Soft devices for this task. I need the code...
hi guys. I am currently using nrf52832 MDBT42Q Series from Raytac. I would like to know that how can I flash the softdevice and my application into the nrf52. My NRFgo unable...
I am currently doing some stress testing to ensure that I am correctly removing peers when the peer manager storage is full.
In this regard, my device is acting as a peripheral...
Hi,
I am developing application using nRF52832, s132, sdk13.2 which is collect sensor data and sent it to server. I have sent data to server using nRf52832 and interface...
Hello,
I'm trying to load BLE UART example on a custom module with nrf52832. I'm using SDK 14.
On the EVK it runs successfully, and I have the following addresses map...
Hello!
I'm trying to perform DFU over BLE using a NRF52 devkit. I'm getting the following error preceded by lots of "Invalid advertising data type" logs:
Traceback (most...
[SOLVED] turn off logging through UART.
Hello
I'm experiencing a strange issue where my device sends a beacon under DEBUG, but does not under RUN.
Due to that I tried...
Hi NordicSemiconductor Community,
I have a problem with the SEGGER Embedded Studio IDE, i want to build my project but i have the following error :
can't open 'C:/Users...
