Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
I use SDK v.2.6.1. To avoid other possible factors affecting the results, I only keep the simplest function in the code which is reading the potential of gpio every second...
In the pairing process among 1 Central and 2 Peripherals
Sometimes the Pairing processing rarely does not work correctly and the following log output:
<err> cis_gateway...
Hello,
We would like to inquire about a technical issue regarding the nRF7002 + nrf5340 with sdk v2.7.0. We have a nrf7002 module connected with nrf5340 through qspi interface...
Hi Support Team
I want to install ZAP tool for NCS V2.8.0 that for Matter development. The command I use to install is pip3 install -r E:/ncs/v2.8.0/modules/lib/matter/scripts...
Hello ：
1.
There is VAMP_IN_XO_LOW in the link, is there VAMP_IN_XO_High （Introduction of relevant information）?
That is, what is the voltage peak-peak requirement...
Hi I am using nRF5 SDK 17.1.0.
Hi I am trying to integrate ANCS in ble_app_uart example. In this example, I am not using bsp library as it is for my custom board.
I am...
Hello Nordic community,
I am facing an issue with flashing the nRF54L15 blinky project to the DK using vscode in Windows 11.
It looks like the compatibility issue between...
I am working on interfacing BLE between my nRF52833 device and both a mobile and a PC. The advertising process is functioning correctly; however, the connection is not establishing...
We have successfully developed a Bluetooth-based tag using the nRF52832 controller and are gearing up for bulk production. While the development phase has been completed successfully...
NRF52840 and NCS
We currently have a large Thread network and plan to configure the network using the Commissioner-Joiner form of network credential distribution.
I...
I need help building the connectivity firmware and getting it working with the examples in pc-ble-driver-py.
If I use nRF Connect Desktop to program a nRF52840 DK, I can...
Hello Nordic DevZone,
I am working with an nRF52840 (from the nRF52840-DK) and I am in the process of connecting the SWD interface to my custom board. I have the following...
I tried 2 different samples in 2.9 with nRF54L15. None are working. Got some SIGTRAP inside
0x0000a4f6 in sym_KOE6VAFEEMU6WWJIX2YPZ4GY7B7U3D4BFIDGCKQ ()
Any ideas ?
