hello, Nrf24LU (Rx) , nRF51822(Tx).
The Nrf24LU Can only receive one packet。
if I use this function twice ， like this：
The Nrf24LU can receive Continuous.
I guess The...
Hi,
I use SDK v10, S110 v8 and dfu_dual_bank_ble_s100_pca10028. My application has dfu support.
I reset to bootloader from application after writing 0x0104 to dfu control...
I have a nRF51822 device.
When the connection interval is 50ms.
The transmission distance can up to 50m+.
But, when the connection interval is 1000ms.
The transmission...
Hi,
I have a simple question. It is possible to use the ble-sniffer nrf51822 on Kali Linux? I found a guide to use it on linux but I don't know if it is the same for Kali...
I've modified Nordic's "Nordic_Keyboard" sample to work with my custom board, just simple modifications to use custom_board.h rather than the default PC10028 configuration...
Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
My application would like to receieve notifications at several different times before a radio notification event. Specifically the application needs to receive notification...
Hello,
i have two operation modes:
One or more devices are bonded and advertising mode with whitelist (BLE_GAP_ADV_FP_FILTER_CONNREQ)
A new proximity central device...
Hi all,
From this forum and the examples given in the "sdk" find two approaches to measuring the battery voltage:
using external divider 10M/2.2M+22nF
using integrated...
In the previous discussion you told me to buy Mod nRF-8001 from olimex and i was also very optimist after going through its design that it can easily be connected to Arduino...
I have an application in which I would like to be able to enable and disable the SoftDevice.
But there are peripherals (Application Timers, Two Wire Interface, etc) that...
Hi,
I'm using PCA10001 connect to a sensor chip.I would like to set the register values for sensor chip as SPI master role and I need to switch to slave role to read the...
Hello,
i just want setup 1Tx and 1 RX using NRF24L01+ chips. but i am confused what should be Transmitter side Tx & Rx and what should be in Rx Tx & RX ? in order to use...
Hi,
There were similar questions already anwsered but none of them work for me. So the situation is as follows. When i program the chip though SWD interface the chip probably...
Hi,
Regarding the source found in "Nordic/Source/ble*" etc (downloaded as part of the nrf518xx SDK
[*] How can I find out which revision/release-tag I'm using. Would...
My design may not connect to a client for most of its operational life but will need to be in advertizing mode whenever not connected. I want to specifiy the advertizing interval...
The nRF Utility app for Android does not support the Galaxy Note 3 yet. Probably because the phone has only been released for a few days so far.
Please add support for...
Hi all,
I am a new user to the BLE technology and to the Nordic's development tools/chips.
I use the nRF51822 development kit and the nRFgo Starter kit to develop a BLE...
In my current project, I have to develop a board with 2 mcu:
nRF51822
STM32F2/F4
The nRF51822 should running S110 SoftDevice and act as a kind of »over the air«...
