Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
I am encountering an issue with my Android OTA app after upgrading to Android 14. The OS seems to enforce the MTU size to 517 by default, but my device firmware ...
Hi,
(+) nPM1300 BUCK1 and BUCK2 efficiencies lower than expected - Nordic Q&A - Nordic DevZone - Nordic DevZone (nordicsemi.com)
Has the above problem been fixed with...
Suppose we have a short distance communication between two nRF52840 devices. And suppose the receiver receives radio waves from other devices disturbing the connection (like...
I am unable to build my application for the Thingy:52 to perform FOTA over BLE. I have configured everything as outlined in the Nordic Developer Academy. FOTA over Bluetooth...
In my application I want to know if a DFU was executed successful and I'm using GPREGRET2 for it.
If a DFU as successful I'm writing GPREGRET2:
nrf_power_gpregret2_set...
Hi There,
I am trying to build a sample application (GNSS) on VS Code for my nRF9160 DK. The build used to be successful, but I noticed that it fails with the following...
Hello,
i am trying to install nRF Command-Line tools in my environment on my company's PC, i am on Windows 11 Enterprise on a Dell Precision 5820 Tower, and I am following...
I am unable to build my application for the Thingy:52 to perform FOTA over BLE. I have configured everything as outlined in the Nordic Developer Academy. FOTA over Bluetooth...
There is a lack of guidance on Blob Transfer Server/Client, so I decided to create and contribute a sample.
In Case ID: 331920, had the idea to add a BLOB Server and Client...
Hello Team,
We wanted to use a NOR Flash GD25Q32E to replace MX25R6435F which is using on the development kit. But we got an error. Please see below screen captures. ...
We are getting below error when flashing hex file in our custom board using a programmer tool but not getting the error when flashing using visual studio flash. 2024-10-15...
Hai,
We are planning to develop a Bluetooth gateway based on nrf52840.
the nrf is connected to esp32 through uart.
The duty of the nrf52840 is
1. It should receive...
Hi,
I'm using nRF Connect SDK v2.7.0 (this error happens with v2.5.0 as well). I'm trying to build the USB Mass Storage sample for FAT FS on flash, in zephyr/samples/subsys...
Hi,
I am writing to a characteristic, and I have noticed that the data is being truncated.
After establishing the connection, I performed an MTU exchange, and the MTU...
