Hello everyone,
I'm trying to set up the Wifi stack on the nRF7002 and use it with MicroPython, but encountering a lot of difficulty with it. I cropped up a network_wlan...
Hi all,
I have a custom board build with an nRF9151. I'm able to connect on int with USB/UART, I can send and receive AT command. Right now I'd like to send certificat to...
Hello, I'm developing a BLE Central application using the nRF52 SDK. The central connects to multiple peripheral devices (nRF52832), each sending 6-byte ADXL345 accelerometer...
I'm having trouble getting the I2C interface working on our nRF54L15-based prototypes. The initial config write to the device fails; specifically, in the twim driver (i2c_nrfx_twim...
Hello,
I just downloaded nRF connect for Desktop App, and plugged in PCA 10100 2. 0. 0 , 2023, 3.
I ran quick start, and this is what I get.
Any explanation on why...
Hi Nordic Team,
I have developed a couple applications for the nRF52833 using Zephyr and have now moved to the nRF54l15. For this new application, power consumption is...
Hi,
I have question about a project I'm running on nRF connect sdk 2.9.1.
I noticed that whenever an i2c sensor device device_init() is returning a value not equal...
Hi
Try to send characteristic notification by invoking sd_ble_gatts_hvx() with the following parameters:
uint32_t err_code = NRF_SUCCESS;
ble_gatts_hvx_params_t params;...
I do run the “nrfjprog --pinreset”,later, the nrfjprog can not find the nrf51 device,WHY?
the nrfprog version is V5.2.0,
I use nrf51822qfaa,s110,keil,etc.
Hi, Guys,
I have a question about chip operation temperature. Will the chip auto reset when the temperature over 75 C? I checked the nRF51822 product specification v3.1...
I would like to learn more about when it is safe to invoke soft device methods and when it is not. For example, are the following 'allowed' to make soft device calls to update...
Update to below: I get data out of the VCP and into Termite for a sub-second when I first power the board (with handshaking enabled), then I get no subsequent data (even though...
Hi,
I have just received a bunch of N550 modules and now I want to try and see if it is possible to update the firmware of these devices without using a JTAG.
If I understand...
I wrote my own ACI interfacing code, so I have questions about some details of the data credit system that most devs may be insulated from by the Nordic SDK.
Section 25...
Hi All,
I was wondering if it was possible to program the nrf51x22 in c++? I am using Keil and I'm trying to convert the examples in the SDK to CPP by adding --cpp to the...
hi,
I have used sd_flash_write() in my code. The scenario is that sd_flash_write() will be called after a DISCONNECT event. And it would wait for system events :
NRF_EVT_FLASH_OPERATION_SUCCESS...
Running S120 2.0 central on nRF51422 QFAAE0 (1504CH) and when I call scan_start() i'm getting 0xDEADBEEF at line 431 in file src\ll_lm.m0.c"
Can anybody shed some light on...
IUsing the Master Control Panel application on my Android device to connect to my nRF51822 module (acting as the GATT server), I have implemented the Device Manager (v10 SDK...
Hello all, to optimize the BOM and size of our device(Tag based on nRF51822), the external divider was replaced by software configuration to measure the battery voltage. In...
Hello,
I have seen, that the BLE MAC is increased by one, in dfu_transport_update_start() (dfu_transport_ble.c).
Can someone give me a short explanation, why this is done...
I have successfully compiled BLE application using tutorials provided on nordic website.
but when I start doing debugging for better understanding find out that I can not...
I configured the bootloader to preserve one page of data ( I configured #define DFU_APP_DATA_RESERVED 0x400 on the bootloader project
I also made the same thing with my...
