I have a custom nRF52832 board with outputs on P0.07 P0.08 P0.09 P0.10 and I want to write to them. 7&8 are working ok but 9&10 are not.
Let me emphasise THE BOARD IS WORKING...
Dear Nordic and community,
I am currently in pre-production phase of designing a PCB based on the NRF9151, and I am a bit confused by the Hardware Device Guidelines, which...
Hi Nordic engineer
I am evaluating a project based on nRF52840 and there is a question need to be confirm before schematic design start.
Due to limitation of power resource...
Hello everyone,
I'm trying to set up the Wifi stack on the nRF7002 and use it with MicroPython, but encountering a lot of difficulty with it. I cropped up a network_wlan...
Hi all,
I have a custom board build with an nRF9151. I'm able to connect on int with USB/UART, I can send and receive AT command. Right now I'd like to send certificat to...
Hello, I'm developing a BLE Central application using the nRF52 SDK. The central connects to multiple peripheral devices (nRF52832), each sending 6-byte ADXL345 accelerometer...
I'm having trouble getting the I2C interface working on our nRF54L15-based prototypes. The initial config write to the device fails; specifically, in the twim driver (i2c_nrfx_twim...
Hi there,
is it possible to share the nrf51 reference layout as p-cad files so they can be (easily) imported into circuit maker / kicad?
I think this would be interesting...
Hi,
In micro_esb.h, it is indicated that the transmission without ACK is not implemented yet. However, there is a parameter named dynamic_ack_enable in the uesb_config...
Hello,
I am getting a 0xdeadbeef assertion at src\soc_radio_timeslot.c line 390. I am using S110 SoftDevice v7.1.0 with nRF51822 revision 2 CEAA. I am using the multiprotocol...
Hi,
i'm newbie to ANT world and i'm trying to create a mesh-like network using broadcast messages and shared channel with nRF51422 SoC and S310 soft-device.
So, i created...
Hi all,
I've been trying to develope a project by using an nRF51822 chip. The project is about to finish. However, I couldn't implement the pstorage module in a correct way...
I am looking to re-install the firmware on my dongle after making it a sniffer but I can't find a hex file for PCA10031. My MasterControlPanel has firmware for PCA10000 should...
Hi
Should I get a characteristic write event ( BLE_GATTS_EVT_WRITE ) with s110 as well with the
following property configuration:
char_md.char_props.write = 0;
char_md...
I try to achieve something similar to IBeacon where data is pushed to any device listening, but where the data is changing over time. Is it possible to (frequently) change...
Hello,
I have recently had to install the nrf tools on a mac computer. The tools have been recently ported to macs, but unfortunately I am getting the following message...
Greetings,
During a connection between two nrf51422s running on S120 (2.1.0) and S110 (8.0.0) with a connection interval of 7.5 ms I get only a maximum RSSI of -42 dBm...
Hello,
I developed a firmware on nrf51422 with nrf51. I use a development board PCA10028.
With this firmware I control the directly the radio registers (Soft Device is...
I have a nRF51822-EK evaluation kit (so, PCA10001) and am trying to get DFU working with an S120 SoftDevice as per the answer posted here:
devzone.nordicsemi.com/.../ ...
nRF51822
I'm interested in setting up the the POFCON to enable me to get a
POFWARN interrupt when the battery voltage drops below 2.7V.
The softdevice is enabled at...
