I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Greetings to everyone.
My name is Toni, I am a beginner. I have a device, which my former colleague left to me, and I can not identify the HWID. How HWID should look like...
Hello,
we are trying to perform FOTA updates with default SLM application based on SDK 2.9.0, but the application always aborts unsuccessfully.
Via AT interface the application...
Hello Everyone,
Happy New Year !
We would like to evaluate nRF54L15 system off/deep sleep mode current consumption. So we have tried the existing example ( https://github...
I just received the nRF21540-DK and am trying to see the range enhancements.
I simply created a new application by copying the "Bluetooth Peripheral" sample in Visual Studio...
Hi,
In the attached hello world example that I modified for the nRF5340DK board, the nRF UARTE serial driver doesn't exit low power mode when I type any characters on my...
Hi everyone,
I've been developing an application using the nRF7002DK, where the nRF5340 SoC communicates with the nRF7002 SoC to connect to a Wi-Fi network, retrieve a JSON...
Hi, I'm quite new with the nrf ecosystem. I'm trying to setup a nrf52833 development board to use an AHT20 as a humidity and temperature sensor. I tried coding my one i2c...
Issue:
The OTBR could run with RCP versions built with SDK v2.3.0 and v2.4.2 but couldn't work with fw from SDK v2.9.0. Hence, I wanted to know which of the latest SDKs...
Hello,
I’m trying to obtain millisecond precision on nRF Connect using the MCU’s internal RTC.
My code:
After 131000 ms, a got:
Could someone help me find...
Hi, I am facing an issue while integrating BLE with the rest of my code. The code crashes when I try to start BLE outside of main() .
Currently, I have placed the BLE initialization...
Hello,
our project which started 7 years ago with SDK13.0 has been migrated some time ago to SDK 15.3 and now to SDK17.1. At the beginning we were quite happy with the RTT...
I'm trying to program an nRF54L15 on the nRF54L15PDK evaluation board with the DEBUG IN SWD pins (P15). On my setup I have a J-Link PLUS connected to P15 and a USB-C connected...
I have the following settings in my prj.conf:
and getting the error
CONFIG_FLASH_MAP was assigned the value y, but got the value n. Missing dependencies: FLASH_HAS_DRIVER_ENABLED...
Dear Nordic team,
we are facing a strange phenomenon - in idle mode (k_sleep(K_FOREVER)) we notice, that the current consumption drastically increases if a magnet is placed...
I have a production system running a modified asset_tracker_v2 sending temperature data to AWS. All is working fine with V2.5.0 on several hundred sensors. I am trying to...
