After i asked this question , i changed to use SDK 8.0.0 hrs "s110_for_dfu",
As the same step to try,
i downloaded softdevice(s110) & bootloader(for 8.0.0)
then opened...
Hello All,
I am trying to create multiple threads for an individual tasks. But when I am creating new thread my program is not working and it's going into some infinite...
I have ASUS ZenPad 10 with Android 5.0.2,
BLE device on nRF51, S110 SDK9 with fixed passkey and encrypted characteristics with following settings
#define SEC_PARAM_BOND...
Looking for someone that has previous experience building multi protocol / time slot topologies using a mix of BLE (central+peripheral) & custom Gazell connections running...
Hi.
I have nRF51422 borad and want to flash to nRF51422 with JLink.
I supplied to 3.3V power to board and is connedted SWDIO to p23, SWDCLK to p24. JLink is connected...
IUsing the Master Control Panel application on my Android device to connect to my nRF51822 module (acting as the GATT server), I have implemented the Device Manager (v10 SDK...
I have successfully compiled BLE application using tutorials provided on nordic website.
but when I start doing debugging for better understanding find out that I can not...
Hi,
IC nRF52833
sdk:nRF5_SDK_17.1.0
1. Does BLE have the concept of signaling test mode and non-signaling test mode?
2. Is DTM in signaling mode or non-signaling mode...
If we are using the 5340 in high voltage mode (VDDH); what IO voltages are used for the debugger interface? Looks like our HW designer has taken the lip voltage 4v3 to 3v5...
Hello,
We are using Nordic sdk 17.1.0, with segger studio of 5.70a.
Here we are trying to merge ble_app_uart example with ble_app_beacon example.
Actually ble_app_uart...
Hello,
I've been playing around with the PPK2. However, when I power a 1KR resistor with 3V I get an incorrect measurement.
The Expected current is 3/1000=3mA, I also...
When I build the smp_svr example, which I think contains firmware update over BLE functionality, the flash memory is reported as about 72% full.
Does this mean when I...
Hi, I use AT command controls the GNSS use Serial LTE modem example in my 91DK board.
I send command as below example,
but my uart tool receive as blow, and i don't...
What is the difference between nRF 5 SDK (downloaded in .zip format) and nRF Connect SDK v1.9.1 ?
I am using VSCode through nRF Connect SDK v1.9.1 and I find it easy to...
I am connecting a nrf52480 board (Adafruit Feather nRF52840 Express) as Connectivity chip and a custom board as Application chip for Nordic serialisation. Able to establish...
I am connecting a nrf 52480 board(Adafruit fether express) to a custom M4 cortex board with the help of nordic serialisation library. I have ported the serialisation library...
Hello all!
I'm using nRF52-DK to develop program which is controlled by smartphone (BLE) and do ADC&GPIO in the circuit.
GPIO acts like this: High-Low-High-Low.... it...
Hi Nordic,
I am working with nRF52840, sdk17.1.0 and do the following test:
I use nrf_gpio_cfg_output(), nrf_gpio_pin_set(); to set gpio P1.00 to high and use nrf_gpio_pin_input_get...
Hi Nordic:
Test with board nrf5340-dk ncs v1.9.1
prj.conf
# Console
CONFIG_LOG = y
CONFIG_LOG_PRINTK = y
CONFIG_LOG_DEFAULT_LEVEL = 3
# UartConsole
CONFIG_UART_CONSOLE...
Good morning:
I'm trying to develop the twi_scanner with the nrfx libraries. Everything seems to compile fine, but at the end of the Build process I get:
d:/ncs/v1.9...
Hi All,
I have a nRF52840 DK board. Which I bought about 1.5 years ago. I used to do some development using Segger Embedded Studio those days.
Now I have setup the Zephyr...
Right now there are 2 supported codecs: SBC and LC3. It also looks like that they are implemented in software.
Can we have other audio codecs (i.e. LC3plus HR, aptX or LDAC...
