I am having an issue with running the initial blinky example that came with the nRF51 PCA10028 SDK in the Eclipse IDE . I will include screenshots of the issue. I believe...
I use nRF51-DK and nRF51-Dongle for a BLE sniffer.
Always the sniffer fails and marked with an error "Encrypted packet decrypted incorrectly (bad MIC)".
It can not be...
Hi,
I'm using long write in one characteristic but if I try to configure this characteritic with write authorization (attr_md.wr_auth = 1) it doesn't work. I need to send...
Hi, I disassembled an Acer Mouse and saw a chip named "NRF A 3152c 1517UH". Can anyone identify the chip or provide me with the data sheet for it.
Regards,
Steve
After i asked this question , i changed to use SDK 8.0.0 hrs "s110_for_dfu",
As the same step to try,
i downloaded softdevice(s110) & bootloader(for 8.0.0)
then opened...
Hello All,
I am trying to create multiple threads for an individual tasks. But when I am creating new thread my program is not working and it's going into some infinite...
I have ASUS ZenPad 10 with Android 5.0.2,
BLE device on nRF51, S110 SDK9 with fixed passkey and encrypted characteristics with following settings
#define SEC_PARAM_BOND...
We need to read/write to an I2C device that uses a 16-bit register addresses (Melexis MLX90632), and the nrf_drv_twi_tx() and nrf_drv_twi_rf() functions seem to be limited...
Hi,
We would like to impelement Pairing and security features in our device. Our device will act as server in peripheral mode. The cleint device should ask for 1 passkey...
Hi Nordic,
I'm referring to this doc but still not quite clear about how to enable the chip for BLE RF HW validation.
infocenter.nordicsemi.com/index.jsp
What would...
Hi,
I have modify the payload of the Light Switch example of the NRF MESH SDK. When I send 50 bytes or less, all works fines : the server nodes received all the bytes...
Hi everyone,
I am developping on a custom board using nRF52840, using MCUboot v1.8.99-ncs1 and nRF Connect sdk v1.8.
For development matters, I would like to change the...
Hi, I want to include the pairing and bonding features in my application.
I want to use the LE secure connection method. For both initiator and responded the IO capabilities...
I adding custom pins declarations through overlay file as in first image with corresponding yaml file ( see attachment) with path .. /dts/bindings/gpio/custom.yaml. The project...
Good Day. I am wondering if anyone could maybe assist me in where I am going wrong with my software.
I have the intention of using a Nrf9160 as a serial modem through AT...
I use nrf9160 to develop a product for customers. The modem is also set to PSM and the log is turned off. However, I find that when the modem is connected to the Internet...
When I try to connect to nrf52840 using J-Link, the following error is detected.
What is the reason for this "Failed to power up DAP"?
- Connecting via USB to probe/ programmer...
Hello nordic support:
We want to measure nRF9160's LTE RX SNR at production stage .
According to the document nwp_034--nRF9160 Hardware.pdf ==> 4.6.1. Following command...
Hi, I am working on nRF52832 as central. When I program it to form Segger Embedded Studio it's working fine but when I upload that .hex file from the nRF Connect device did...
Hi there,
We are designing a coin cell (3 V nominal) battery powered product; we'd like the ability to run it all the way down to 2.0 V for maximum lifetime. To get the...
Board: nRF52833
SoftDevice: s140
SDK version: 17.0.2
I am trying to implement OTA buttonless DFU feature in my custom device (USB Device) which is a central device....
