I created xml file for heartrate server using bluetooth developer studio and the plugin nRF8001_Arduino (plugin nordic semiconductor for arduino)
the generated xml file...
I read this older post ( devzone.nordicsemi.com/.../) and have a similar issue but with enough differences that I felt it was worth a new question.
I have an STM32 MCU...
I am having an issue with running the initial blinky example that came with the nRF51 PCA10028 SDK in the Eclipse IDE . I will include screenshots of the issue. I believe...
I use nRF51-DK and nRF51-Dongle for a BLE sniffer.
Always the sniffer fails and marked with an error "Encrypted packet decrypted incorrectly (bad MIC)".
It can not be...
Hi,
I'm using long write in one characteristic but if I try to configure this characteritic with write authorization (attr_md.wr_auth = 1) it doesn't work. I need to send...
Hi, I disassembled an Acer Mouse and saw a chip named "NRF A 3152c 1517UH". Can anyone identify the chip or provide me with the data sheet for it.
Regards,
Steve
After i asked this question , i changed to use SDK 8.0.0 hrs "s110_for_dfu",
As the same step to try,
i downloaded softdevice(s110) & bootloader(for 8.0.0)
then opened...
hi all, 1. may i know how to get started of designing an AOA, mainly on how to send a CTE packet from TX to RX is there any code base or command that i can use? 2. i had noticed...
I am trying to establish a tunnel from ZigBee client to ZigBee server on nRF52840 using "nRF5 SDK for Thread and Zigbee v4.1.0".
Starting with the examples "examples\zigbee...
Hi everyone!
Challenge :
I'm trying to stream data from 9 nrf52832 (12 bytes each) to a computer, hopefully at 25 Hz at least (it seems more than realistic!).
Dream...
Hi !
I want to send simple HCI commands, such as reset, to the nRF5340 via UART. Therefore, I'm using the sample "hci_uart" available with nRF Connect SDK v1.5.0. I am sniffing...
It would be great to get some reassurance on this design. Is it ok for production i.e. is robust and within limits?
I am successfully driving an smd rgb led by sinking 2ma...
I am using the https fota, aws sample OK.
testd the aws certificate via Linux PC this way:
openssl s_client -connect kamacodeetrog.s3.us-east-2.amazonaws.com:443
now...
I'm trying to write the stripped down version of UART driver myself and having a few issues:
I enabled the UART, along with other registers as shown below
but when I...
on Ubuntu 20.04.2 LTS i have setup nRF connect SDK. When i try to configure segger Embedded studio. I am getting the error "create nordic project.py failed". I have connected...
The temperature sensor that i am using is analog. As mentioned above I have already gotten the temperature value using sd_temp_get().I also wish to send the values of voltage...
Hello all,
We are using Segger Embedded Studio (SES) v5.20 ,SDK v17.0.2 ,NRF52840DK board
The issue we are facing is we have a .msbl (kind of binary file)( file size 180KB...
Hi all
I want to trigger a limit event on a signal, which I receive on AIN0. Since the signal does not always have the same baseline, I set the limits with the first measurement...
This has been happening for a very long time when building nRF connect SDK applications on a windows 10 machine via the command line with cmake and ninja. In an application...
Had this linking error when I tried to build the bootloader for nrf9160dk_nrf52840 calling
west build -b nrf9160dk_nrf52840 ..
the same error ocurred using
cmake - GNinja...
I am new to this community although I have already been exposed to products with Nordic components.
I have been reading a lot and watching recorded webinars the past few...
Hi everyone,
I am trying to send a custom zigbee message by using this function zb_zcl_finish_and_send_packet_new() with a callback function to free the buffer after send...
