Hi,
I'm using long write in one characteristic but if I try to configure this characteritic with write authorization (attr_md.wr_auth = 1) it doesn't work. I need to send...
Hi, I disassembled an Acer Mouse and saw a chip named "NRF A 3152c 1517UH". Can anyone identify the chip or provide me with the data sheet for it.
Regards,
Steve
After i asked this question , i changed to use SDK 8.0.0 hrs "s110_for_dfu",
As the same step to try,
i downloaded softdevice(s110) & bootloader(for 8.0.0)
then opened...
Hello All,
I am trying to create multiple threads for an individual tasks. But when I am creating new thread my program is not working and it's going into some infinite...
I have ASUS ZenPad 10 with Android 5.0.2,
BLE device on nRF51, S110 SDK9 with fixed passkey and encrypted characteristics with following settings
#define SEC_PARAM_BOND...
Looking for someone that has previous experience building multi protocol / time slot topologies using a mix of BLE (central+peripheral) & custom Gazell connections running...
Hi.
I have nRF51422 borad and want to flash to nRF51422 with JLink.
I supplied to 3.3V power to board and is connedted SWDIO to p23, SWDCLK to p24. JLink is connected...
Dear Nordic expert,
I'm using nRF52840 as central with SDK 16.0.0.
I establish a connection with a peripheral (phone) and then I need to drop the connection. I set a timer...
Hi, everyone on the community
When using the BLE_APP_UART example, the serial port sends a packet of data to the mobile phone every 10ms, resulting in the device disconnecting...
I want to have a very stripped down version of the cat-tracker-app that just deals with settings, so I can import what is useful to an existing web application. I am new to...
I have succesfully got extended advertising working using the nRF SDK on the nRF52 DK, however I haven't been able to assign it a 128 bit service guid.
Setup:
The device...
Hi,
I want to add DFU to our board running SDK11 S130 but facing some problems.
I followed the instructions on infocenter, and started with ble_app_hrs example (from here...
hello,
i am using nrf52840 with our cutomised board and trying to achieve long range using coded phy and using that long range demo example as base i have sucessfully changed...
Hi All, I try to run the example GFX in sdk 17.02.
I wired the TFT :
---VCC ------------------ +3V ---GND ------------------ GND ---CS -------------------- P1.09 --...
Hello ,
NRF52840
sdk 15.2
In my application using ble central example in nrf52840 , i am able to write data in led characteristics and getting notification on HVX using...
Hi, I have tried to add support for BOS descriptor by appending a custom class generated from the Dummy example. The "main" class is the HID generic class, but with the NRF...
Hello
I only used PWM_library, but this is my first time using PWM_driver. Simply controlling the duty cycle of multiple channels has been successful, but I am not sure...
A little backgroud for my project. The goal of the project is to be able to identify the proximity of beaconing devices in an area to a specific observer which then reports...
Hi, Below is the mapping of RAM on the 840 from the infocenter. We want to utilize the functionality to turn off unused RAM (via sd_power_ram_power_clr), but we see that if...
I am using SoftDevice s140v6.1.1. The behavior is I was able to program nRF52840 through JTAG without any issue. I am checking out the OTA firmware update feature and nRFConnect...
Hello Everyone,
I am developing one product using nRF52840 MCU, in this project my master controller is nRF52840 MCU and the host is STM-based MCU.
My goal is to make...
Hi,
I am configuring a test software to generate CW signals at channel 0, 19 and 39. Currently I'm using the nRF52840dk, later a custom board. The channel number is calculated...
