I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hi,
I am working on a project which will connect to device having static mac address . My job is to make sure that the device will connect to device having BLE_GAP_ADDR_TYPE_RANDOM_PRIVATE_RESOLVABLE...
Hello,
I wanted to replicate and build the LED Button Service using my own custom service. I used the template BLE project as a starting point.
I am using nRF52 DK, and...
for (int i = 0; i < LEDS_NUMBER; i++) { bsp_board_led_off(0); nrf_delay_ms(500); bsp_board_led_on(0);
}
in this code only the first command gets executed.
It turns off...
Hi,
We have several boards on hand which fall into two categories:
Category A: Our application has been programmed with JTAG in the past
Category B: Out application...
Hello!
I'm trying to DFU an NRF52 device on a custom board using nrfutil
I'm able to DFU the device using the NRF Connect v3.3.0 software together with an nrf52840...
Hello,
My problem statement is something like this:
Implement a Transmit Enable (TxEn) on a GPIO pin.
TxEn should be initialized low.
TxEn should be pulled...
I am new to Nordic and i am using nRF52840 DK, - SDK 15.2.0 - s140. I have written an application by modifying the Heart rate Monitor example. My program acquires and sends...
hi,
I am working with usb dfu bootloader for nrf52833. I set the bootloader entrance mode to GPREGRET only. before enter bootloader, I set NRF_POWER->GPREGRET = 0x00000001...
I downloaded SDK V17.0.0.9 and opened BLE_APP_UART example from /ble_peripheral folder on IAR EWARM. I choosed ble_app_uart_pca10040e_s112 and compiled without problems. ...
Our system is currently using the ble_radio_notificaiton components provided by nrf5_sdk version 16, and we have noticed that occasionally after ble pairing + bonding operations...
Hi
I use nRF52840 demo board load the firmware( C:\sdk\nRF5_SDK_for_Thread_and_Zigbee_v4.1.0_32ce5f8\examples\thread\cli\ftd\uart\pca10056\blank\ses )
the putty can work...
Hi Team,
We have developed our application with SDK v1.20 and as v1.30 is released so we moved to v1.30 and stick to it.But project is not opening in sdk v1.30 and got...
Hello,
if one wants to start the app from scratch, what is the right way to create west.yml file?
Say we want to start from NCS 1.3.0.
Thank you & best
Oleh
hello Nordic
i am using nrf52832, sdk 16.0 s132 v7.0.1
i used the secure_uart_bootload example, the start flash in the example starts at 64000, though in this link the...
Hi, I am working on nRF52840 DK.
I uploaded ble_app_template on board and now trying to connect with nRF Connect and getting the following issue. Any suggestions, please...
