Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Using the SDK11 bootloader, if I recompile the bootloader, package it with nrfutil 0.5.3, and perform a DFU update the original bootloader is erased but the new bootloader...
Hello,the SDk is nRF5_SDK_15.0.0_a53641a,the MCU is 52840.
I want to memory map it and refresh it .
that's 240x320 x bytes per pixel, it's 16-bit RGB, so 240x320x2 = 150k...
A manufacturer of nrf52832 module has replaced by mistake the values of C1.C2 capacitors that are connected to the 32Mhz oscillator from 12pf to 24pf and 27pf.
What will...
Hi,
I'm using NRF52 and used inbuilt UART for communication with host controller.now i need one more uart port for log printing.
so how we can achieve on NRF52?
Thanks...
Hi Nordic team,
I'm trying to run demo SPI programs from NRF5 SDK. I want to create simple SPI communication between two dongles, of which one would be master and the other...
Hi, this is my first post here, so please forgive if category/description is not complete.
I'm trying to do a quick proof of concept using ZB ZCL Tunneling. ZED is a client...
Good morning,
I'm developing an app for NRF52832 SDK 15.3, SD 132 6.1.1 with NUS service. Moreover my app has DFU and Peer Manager with LESC JustWorks security and other...
Hello All,
I am working on an indoor positioning project where I want to send/POST request RSSI values to the server/frontend. So is it possible to send RSSI values to the...
Hello,
we have a problem with a BLE connection state function. We are working with an NRF52832 device and SDK 14. The device itself works in central and peripharel mode...
Thanks in advance for any advice!
We are developing an ultra low powered network. There will be a remote control with numerous buttons. This will connect to 2-10 peripheral...
hai , I would like to program cli uart in pca10059, what are all things to change in openthread stack in order to change UART pin configure and how to compile it ? I use only...
I am trying to implement cli uart in custom board, for which there comes need for me to recompile openthread stack (in order to change UART and LED pin configuration) in GCC...
I was just working with the ble_app_uart example in nrf5_SDK_12.2.0. Minor modification were done to the main function. The build output:
linking...
._build\nrf52832_xxaa...
The site is just showing a product brief PDF, where can I access the full datasheet? Is the crystal oscillator on board or an external connection is required?
Hi,
I am using SDK version 15.3.0. I am trying to implement the ble_dfu example. By default, advertising name is set to "DfuTarg". I want change this to a custom name. How...
