Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I'm working on a project that have with multirole to do, i have 3 device one act as master after a button is pressed, now i want to establish a connection between...
Hi,
I am having some issues with DFU and Keil.
I am loading Softdevice s140 v7.0.1 via nRF Connect and then programming a secure BLE bootloader using nrfjprog.
The bootloader...
Hi everybody,
I have a question about the number of data pakets which I can send with the BLE. Every data paket has a range of 20 Byte.
Now I want to send about 55 of...
Hi, I need to do some power analysis of an application I am working on. I have a Power Profiler Kit, but it will not work with nRF Connect currently.
I have two machines...
My application is on the nRF52840 Dongle using ESB protocol, receiving data from an number of PTXs, . The device appears as an HID.
I would like to add Buttonless DFU, without...
Hi,
I am new here and I have some issues with Zigbee reporting implementation.
I am trying to implement a reporting feature between a coordinator and an end device, which...
Hi,
Attached is Cmake error log from one of the failed builds.
This is a new MBP with freshly installed nRF Connect - following tutorial.
Anyway, I am not able to open...
Hi all,
since new version of IOS nRF Mesh App I can't finish provisioning of my nRF52840 DK with flashed light example client.
When I start provisioning for the device...
Hi,
I am using NRF52832 with SDK 15.3 and SD 132 on our custom board ( VDD 1.96V ). I started with with the ble_app_template example for our application. Upon measuring...
Hi Nordic
I am using saadc example now, my device output voltage range is -4v~4v.
my saadc config:
VDD: 3.3V
Reference: VDD/4
Gain: 1/4
Mode: SINGLE_ENDE
i got...
Hi, I am new to BLE, I am trying to send and receive data over BLE and print them in Uart as well in both devices respectively.
And I downloaded lastest NRF5-SDK, I have...
Could you, please, direct me to any example (if available) how to manage lost bond with nRF52832/ SDK16 BLE?
Let say very common situation that will try to demonstrate with...
Hi all,
I have hardware as below:
nRF52840-DK - as an advertiser and the same type of board nRF52840-DK - as a scanner
My problem is that I want to send more data than...
