Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Good afternoon,
At the place I'm working there's 2 main projects using the nordic SDK, while one runs on the 12.3 version, the other is very outdated and still runs on...
Hi,
I'm having a problem at the moment with code based on Espruino on nrf52.
I connect as follows:
ble_gap_scan_params_t m_scan_param;
memset(&m_scan_param, 0,...
I've seen a few post that have similar issues but none that solve my problem.
I have two uarts (uarte0 and uarte1).
I disable them before going to sleep.
I wake with...
Hello,
I cannot successfully flash an nRF9160-Dk to a usable AT modem state using a brand new install of nRFConnect on Windows10, following this Blog post guidance - https...
I am working on 802.15.4 using nrf52840 and sdk 15.2. I want the receiver node to scan the network for beacons transmitted by the transmitter node for 100ms, go to sleep for...
So its seems nrf9160 docs recommend having VDD_GPIO only at 1.8v ... that running at 3.0v (or 3.3v) will compromise LTE performace.
I have 3.3v rail and 3.3v SPI device...
Hi Folks,
I'm trying to use the Power Profiler Kit. Unfortunately I keep getting 'Failed to start the PPK'. I've updated the drivers (and can program the nrf52832 DK with...
In the nRF52840 Product Specification v1.1 ( HTML ) , description of the QDEC peripheral, Table 77 on page 275 ( direct content link) , it appears to indicate that the LED...
Hi,
We have an freertos based app (SDK14.2).
Recently we have added a WDT support in the following manner:
The init code initializes the WDT reload value to T+3...
hi all, i am using the uart with it's dma to transfer data into the nrf9160, but some of the data is lost in it's way. here are some examples of the loss count in bytes from...
Hello,
I'm using several nRF52840 boards to setup a bluetooth mesh network. Im using the python script "interactive_pyaci.py" to setup the mesh. The mesh is working and...
Hi, As the title asks, I am using the lte_ble_gateway example project on the nRF9160 DK. I am able to connect one nRF52840 DK to the nRF9160 DK over BLE. I am trying to connect...
We have a board that has become unresponsive to programming. It worked well to program about 4 times and then is no longer responding to the J-Link device. The application...
