I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hi All,
I am going to get EMI/EMC testing for my custom board made on nRF52832 WLCSP package. Can you please share/suggest the firmware used in EMI/EMC testing.
hi everyone
i want use s130 with my ble nrf1822 i'm wondering about the modifiaction that i have to do under keil 5 in option for target for example the configuration that...
Hi,
I try to use the dfu update OTA with ble secure bootloader.
If the Flash is erased and only the SD v5.0.0 and the own Bootloader are programmed a update OTA is working...
When making a bluetooth mesh network, what is a good rule of thump for the ratio between servers and clients?
I am thinking of implementing the server-client-model scheme...
Hi Engineers!
We used SDK13 for our Project (multilink BLE with 1xServer & 4x PeerS) and now move to SDK14.2, almost done except only USBD.
if we use SDK13 driver...
I've already tried before using ADXL345 using nRF51822 using mbed compiler this is the link.. os.mbed.com/.../
but that program can't get ADXL345 data, just UART nRF51...
I'm trying to debug a project I recently migrated to eclipse but my Peripheral Registers are empty with the error message "There are no peripherals descriptions available...
I'm building a new application based on the no softdevice template example. I pulled in the code from the UART BLE example to redirect printf to the serial interface and that...
Seems i can not find where nrf_dfu_set_adv_name_init is defined? It seems not in SDK source files, neither can find any sign on SDK documents.
Thank you.
Hello,
I have a nRF52832 Breakout Board from SparkFun. I can see from their tutorial that I can program this board using the serial bootloader that they have burned into...
Hi everyone,
I make the project whith nrf51822 BLE module and need to configure the bluetooth service characteristic as input/output for reading and writing the string-information...
Product: nRF24Lu1+
If I use the nRFGo and the nRF24LU1+ Development kit, must I use the Keil tools to be able to access the debugging port? I develop in linux and use the...
Hi everyone,
My configuration:
nrf52832 microcontroller
Softdevice S132 V4.0.2
Nordic SDK 13.0
IDE: Eclipse
I'm working with a "Stand-alone can bus controller...
Hello All,
I am working nrf51DK and i am using ble_app_uart application with s130 softdevice.
Now my query is I am trying to send some data from my mobile application...
